KYMCO Kymco UXV 500i Скачать руководство пользователя страница 138

Страница: 138 / 426

7. ENGINE REMOVAL/INSTALLATION

7-9

UXV 500

Install the compression spring into the

pinion gear.

Move the engine rearward and engage the

rear propeller shaft into the pinion gear.

Install the upper engine mounting bolt and

nut loosely.

Install the rear lower engine mounting bolt

and nut loosely.

Install the engine hangers and four engine

hanger nuts loosely.

Install the front lower engine mounting bolt

and nut loosely.

Tighten the four engine hanger nuts to the

specified torque.

Torque:

3.5 kgf-m (35 N-m, 25 lbf-ft)

Tighten the all engine mounting bolts and

nuts to the specified torque.

Torque:

6 kgf-m (60 N-m, 43.5 lbf-ft)

Apply grease Pinion Gear

Compression Spring

Apply lightweight lithium-soap base

grease to the pinion gear splines.

＊

Install the joint boot securely.

＊

Lower Engine Mounting Bolt/Nut

Upper Engine Mounting Bolt/Nut

Содержание Kymco UXV 500i











































































































































































































































































































































































































































Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды

KYMCO Kymco UXV 500i, Руководство по обслуживанию

Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды