KYMCO Kymco UXV 500i Скачать руководство пользователя страница 124

Страница: 124 / 426

. COOLING SYSTEM

6-17

UXV 500

WATER TEMPERATURE
SENSOR

Remove the center cover and gear shift of

lever bolt
Disconnect the water temperature
sensor connector.

Remove the water temperature sensor from

the water joint.

INSPECTION

Connect the water temperature sensor to the

ohmmeter and dip it in oil contained in a

pan which is placed on an electric heater.
Gradually raise oil temperature while

reading the thermometer in the pan and the

ohmmeter connected. If the resistance

measured is out of specification, replace the

temperature gauge with a new one.

Temperature

Standard resistance

50ºC

123.9

–

478.9

Ω

100ºC

–

29.3

Ω

After the water temperature sensor has been

installed, fill coolant and perform air

bleeding (refer to the “

COOLANT

REPLACEMENT

” section in this

chapter).

INSTALLATION

With thread lock applied to the threaded

part, tighten the water temperature sensor.

Torque:

0.8 kgf-m (8 N-m, 5.8 lbf-ft)

Water Temperature Sensor

Thermometer

Water joint

Water Temperature Sensor

●

Handle the water temperature sensor

carefully as it is vulnerable to impact.

●

Do not allow the water temperature

sensor and the thermometer to come in

contact with the bottom of the pan.

＊

Содержание Kymco UXV 500i











































































































































































































































































































































































































































Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды

KYMCO Kymco UXV 500i, Руководство по обслуживанию

Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды