KYMCO Kymco UXV 500i Скачать руководство пользователя страница 116

Страница: 116 / 426

. COOLING SYSTEM

6-9

UXV 500

INSPECTION

Visually inspect the thermostat for damage.

Heat the water with an electric heating

element to operating temperature for five

minutes.
Suspend the thermostat in heated water to

check its operation.

Replace the thermostat if the valve stays

open at room temperature, or if it respond at

temperatures other than those specified.

Thermostat begin to open:

−

C (176

−

183

Valve lift:

8 mm (0.3 in) minimum at 95

C (203

INSTALLATION

Install the thermostat into the housing with
its air bleed hole facing up and aligning
bleed hole with the tab in the housing.

Thermostat

Thermometer

●

Keep flammable materials away from

the electric heating element.

●

Do not let the thermostat or

thermometer touch the pan, or you will

get false readings.

＊

Tab Align

Air Bleed Hole

Содержание Kymco UXV 500i











































































































































































































































































































































































































































Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды

KYMCO Kymco UXV 500i, Руководство по обслуживанию

Результаты поиска

Содержание Kymco UXV 500i

Отзывы:

Бренды по названию

Популярные бренды