manualshive.com logo in svg

KYMCO Kymco UXV 500i, Руководство по обслуживанию

Поделиться
Скачать
KYMCO Kymco UXV 500i Скачать руководство пользователя страница 11

1

. GENERAL INFORMATION

1-9

         UXV 500

„

After routing, check that the wire harnesses
are not twisted or kinked.

„

Wire harnesses routed along with handlebar
should not be pulled tight, have excessive
slack or interfere with adjacent or
surrounding parts in all steering positions.

„

When a testing device is used, make sure to
understand the operating methods
thoroughly and operate according to the
operating instructions.

„

Be careful not to drop any parts.

„

When rust is found on a terminal, remove
the rust with sand paper or equivalent
before connecting.

Do you understand
the instrument? Is the
instrument set
correctly?

Remove Rust !

Содержание Kymco UXV 500i











































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды