background image

VHD5 Rigging Manual · VHD5 Cabinet

VHD5 Cabinet

  1.  Remove the transport cover from the VHD5.0 cabinet  
 

  and wheel into position directly below the flown VHD8.10    

   cabinets.

  2.  Lower the two VHD8.10‘s, so that they rest completely 
 

  on top of the VHD5.0 cabinet with their feet interlocked.

HAZARD! 

DO NOT rotate the 

connecting bars into place until the 
VHD8.10 cabinets have been landed 
accurately on top of the VHD5.0 cabinet. 

Doing so can damage the rigging bars 

and the cabinets.

  3.  Remove the push pins at the top of the VHD5.0 and the bottom of the VHD8.10. Then rotate the silver knob on
 

  both sides of the VHD5.0 which will allow the rigging arms to raise up in to the bottom VHD8.10. Once in position

 

  replace the push pins on the VHD5.0 and the adjacent VHD8.10 in to the respective locking point no’s 1 and 2.

HAZARD! Don’t forget, that this always has to be done on both sides. 

Failure to do so could cause the rigging arms to be bent and become inoperable.

  4.  At the rear of the cabinet connect one of the Blue LK connectors into the blue LK socket, and the Yellow LK connector
 

  into the Yellow socket on the VHD5.0 cabinet.

  5.  Remove the bottom push pins of the VHD5.0 which will release the transport cart in the same way as on the VHD8.10  
 

  cabinets. Replace the push pins in the bottom holes of the VHD5.0 cabinet.

  6.  Raise the system slightly, and remove the VHD5.0 transport cart.

VHD5 R

igging M

anual · 

VHD5 C

abinet

15

Содержание VHD5 Series




















Отзывы: