Kubota BX2350D Скачать руководство пользователя | Manualshive

Страница: 83 / 102

background image

63

PERIODIC SERVICE

ENGLISH

B

Adjusting Fan Belt Tension

To avoid personal injury:

A

Be sure to stop the engine and remove the key
before checking belt tension.

1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between

pulleys.

3. If tension is incorrect, loosen the alternator mounting

bolts and, using a lever placed between the alternator
and the engine block, pull the alternator out until the
deflection of the belt falls within acceptable limits.

4. Replace fan belt if it is damaged.

B

Adjusting HST Neutral Spring (for Speed

Control Pedal)

To avoid personal injury:

A

Do not operate if tractor moves on level ground
with foot off speed control pedal.

A

If tractor moves on level ground with foot off
the pedal, or, if the pedal is too slow in
returning to "NEUTRAL" position when
removing the foot from the pedal, consult your
local KUBOTA Dealer.

The HST neutral spring located under the front right side
of the fender can adjust returning speed of speed control
pedal.
Consult your local KUBOTA Dealer for service.

Proper fan belt
tension

A deflection of between 7 to 9 mm
when the belt is pressed in the
middle of the span.

(1) Bolt

(A) Check the belt tension

(1) HST neutral spring
(2) Adjusting nut

«
...
81
82
83
84
85
...
»

Содержание BX2350D







































































































Отзывы:

Нет отзывов

Похожие инструкции для BX2350D

Бренд: SaMASZ Страницы: 29

Бренд: Vestil Страницы: 19

Бренд: Husqvarna Страницы: 68

Бренд: Husqvarna Страницы: 104

Бренд: Siemens Страницы: 96

Бренд: Cub Cadet Страницы: 48

Marathon RAMJET Signature J-250SC

Бренд: Dover Страницы: 47

SuperSpread PTO 135

Бренд: PEQUEA Страницы: 28

Бренд: Kellfri Страницы: 8

Craftsman 944.101040

Бренд: Sears Страницы: 52

Бренд: Simplicity Страницы: 36

Sovereign 499-3112H

Бренд: Simplicity Страницы: 40

Landlord 756 3410S

Бренд: Simplicity Страницы: 40

Sovereign 3416H

Бренд: Simplicity Страницы: 40

Бренд: Simplicity Страницы: 40

Бренд: Simplicity Страницы: 40

Baron System 7013S

Бренд: Simplicity Страницы: 44

Бренд: Simplicity Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды