Kubota BX2350D Скачать руководство пользователя страница 5

Страница: 5 / 102

CONTENTS

ENGLISH

SAFE OPERATION ............................................................................................

SERVICING OF TRACTOR......................................................................................... 1

SPECIFICATIONS....................................................................................................... 2

SPECIFICATION TABLE ......................................................................................... 2
TRAVELING SPEEDS ............................................................................................. 3

IMPLEMENT LIMITATIONS ........................................................................................ 4

INSTRUMENT PANEL AND CONTROLS................................................................... 7

PRE-OPERATION CHECK ......................................................................................... 9

DAILY CHECK ......................................................................................................... 9

OPERATING THE ENGINE....................................................................................... 10

STARTING THE ENGINE ...................................................................................... 10

Cold Weather Starting .................................................................................................... 12
Block Heater (Option) ..................................................................................................... 12

STOPPING THE ENGINE...................................................................................... 12
WARMING UP ....................................................................................................... 13

Warm-up and Transmission Oil in the Low Temperature Range.................................... 13

JUMP STARTING .................................................................................................. 13

OPERATING THE TRACTOR ................................................................................... 14

OPERATING NEW TRACTOR .............................................................................. 14

Do not Operate the Tractor at Full Speed for the First 50 Hours.................................... 14
Changing Lubricating Oil for New Tractors..................................................................... 14

BOARDING AND LEAVING THE TRACTOR ........................................................ 14
STARTING ............................................................................................................. 14

STOPPING............................................................................................................. 21

Stopping.......................................................................................................................... 21

CHECK DURING DRIVING ................................................................................... 22

Содержание BX2350D







































































































Результаты поиска

Содержание BX2350D

Отзывы:

Kubota BX2350D, Руководство оператора, Страница: 5 / 102

Результаты поиска

Содержание BX2350D

Отзывы: