manualshive.com logo in svg

Kubota BX2350D, Руководство оператора

Поделиться
Скачать
Kubota BX2350D Скачать руководство пользователя страница 46

OPERATING THE TRACTOR

26

ENGLISH

B

Trailer Electrical Outlet

A trailer electrical outlet is supplied for use with trailer or
implement.

C

Function of each terminals in trailer electrical
outlet

B

Operating on a Slopes and Rough Terrain

To avoid personal injury:

A

Always back up when going up a steep slope.
Driving forward could cause the tractor to tip
over backward. Stay off hills and slopes too
steep for safe operation.

A

Avoid changing gears when climbing or
descending a slope.

A

If operating on a slope, never disengage shift
levers to "NEUTRAL". Doing so could cause
loss of control.

A

Do not drive the tractor close to the edges of
ditches or banks which may collapse under the
weight of the tractor. Especially when the
ground is loose or wet.

1. Slow down for slopes, rough ground, and sharp turns,

especially when transporting heavy, rear mounted
equipment.

2. Before descending a slope, be sure that the range

lever is in the low "

" so that speed can be

controlled without using brakes.

B

Transport the Tractor Safely

1. The tractor, if damaged, must be carried on a truck.

Secure the tractor tightly with ropes.

2. Follow the instruction below when towing the tractor:

Otherwise, the tractor’s powertrain may get damaged.

A

Set the all shift levers to "NEUTRAL" position.

A

If possible, start engine and select 2WD, if creep
speed is fitted ensure that it is disengaged.

A

Tow the tractor using its front hitch or drawbar.

A

Never tow faster than "10 km/h (6.2 mph)".

B

Directions for Use of Power Steering

1. Power steering is activated only while the engine is

running. While the engine is stopped, the tractor
functions in the same manner as tractors without
power steering.

2. When the steering wheel is turned all the way to the

stop, the relief valve is activated. Do not hold the
steering wheel in this position for a long period of time.

3. Avoid turning the steering wheel while the tractor is

stopped, or tires may wear out sooner.

4. The power steering mechanism makes the steering

easier. Be careful when driving on a road at high
speeds.

(1) Trailer electrical outlet

Terminal

Function

(1)

Turn signal (LH) 

(2)

---

(3)

Ground

(4)

Turn signal (RH)

(5)

Tail (RH)

(6)

Brake stop

(7)

Tail (LH)

Содержание BX2350D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды