manualshive.com logo in svg

Kubota BX2350D, Руководство оператора

Поделиться
Скачать
Kubota BX2350D Скачать руководство пользователя страница 75

55

PERIODIC SERVICE

ENGLISH

B

Checking Engine Oil Level

To avoid personal injury:

A

Be sure to stop the engine before checking the
oil level.

1. Park the machine on a flat surface.
2. Check engine oil before starting the engine or 5

minutes or more after the engine has stopped.

3. To check the oil level, draw out the dipstick, wipe it

clean, replace it, and draw it out again. Check to see
that the oil level lies between the two notches.
If the level is too low, add new oil to the prescribed
level at the oil inlet.
(See "LUBRICANTS" in "MAINTENANCE" section.)

A

When using an oil of different maker or viscosity from
the previous one, remove all of the old oil and oil filter. 
Never mix two different types of oil.

A

If oil level is low, do not run engine.

B

Checking Transmission Fluid Level

1. Park the machine on a flat surface, lower the

implement and shut off engine.

2. To check the oil level, draw out the dipstick, wipe it

clean, replace it, and draw it out again. Check to see
that the oil level lies between the two notches.
If the level is too low, add new oil to the prescribed
level at the oil inlet.
(See "LUBRICANTS" in "MAINTENANCE" section.)

A

If oil level is low, do not run engine.

(1) Oil inlet
(2) Dipstick

(A) Oil level is acceptable within this range.

(1) Oil inlet
(2) Dipstick

(A) Oil level is acceptable within this range.

Содержание BX2350D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды