Kubota BX2350D Скачать руководство пользователя страница 40

Страница: 40 / 102

OPERATING THE TRACTOR

ENGLISH

Hand Throttle Lever

Pulling the throttle lever back increases engine speed,
and pushing it forward decreases engine speed.

Parking Brake Pedal

To release the parking brake, depress the brake pedal
again.

Speed Control Pedal

To avoid personal injury:

Do not operate if tractor moves on level ground
with foot off Speed Control Pedal.

Forward Pedal

Depress the forward pedal with the toe of your right foot to
move forward.

Reverse Pedal

Depress the reverse pedal with the heel of your right foot
to move backward.

To prevent serious damage to the HST, do not adjust
the stopper bolts.

When you stand up from the seat with the speed
control pedal stepped on, the engine will stop
regardless of whether the machine is moving or not.
This is because the tractor is equipped with Operator
Presence Control system (OPC).

7. Accelerate the Engine.

(1) Hand Throttle lever

"INCREASE"
"DECREASE"

8. Unlock the Parking Brake.

(1) Brake pedal

9. Depress the Speed Control Pedal.

(1) Speed control pedal
(2) Stopper bolts

(A) "FORWARD"
(B) "REVERSE"

Содержание BX2350D







































































































Результаты поиска

Содержание BX2350D

Отзывы:

Похожие инструкции для BX2350D

Бренды по названию

Популярные бренды

Kubota BX2350D, Руководство оператора

Результаты поиска

Содержание BX2350D

Отзывы:

Похожие инструкции для BX2350D

Бренды по названию

Популярные бренды