manualshive.com logo in svg

Kubota BX2350D, Руководство оператора

Поделиться
Скачать
Kubota BX2350D Скачать руководство пользователя страница 2

Abbreviations

Definitions

ABBREVIATION LIST

Two Wheel Drive
Four Wheel Drive
American Petroleum Institute
American Society of Agricultural and Biological Engineers, USA
American Society for Testing and Materials, USA
Deutsches Institut für Normung, GERMANY
Dual Traction [4WD]
High Speed-Low Speed
Hydrostatic Transmission
Meters Per Second
Power Take Off
Right-hand and left-hand sides are determined by facing

in the direction of forward travel
Roll-Over Protective Structures
Revolutions Per Minute
Revolutions Per Second
Society of Automotive Engineers, USA

2WD
4WD

API

ASABE

ASTM

DIN

DT

Hi-Lo

HST

m/s

PTO

RH/LH

ROPS

rpm

r/s

SAE

manufacturer or distributor of the machine
the model designation of the machine
the name or type of publication
the part number of this Operator’s Manual

the publication date
the language in which the manual is written

Kubota Corporation

BX2350D

Operator's Manual

K2683-7125-3

September 28, 2012

the date of issue

March 9, 2012

English

Intended use

This machine is designed solely for use in customary agricultural or similar operations. Use in any other way is 

considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, 

service, and repair as specified by the manufacturer, also constitute essential elements of the intended use.

This machine should be operated, serviced, and repaired only by persons who are familiar with its particular 

characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognized regulations on safety and occupational medicine, 

and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting 

damage or injury.

Содержание BX2350D







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды