Kubota BX2350D Скачать руководство пользователя страница 49

Страница: 49 / 102

PTO

ENGLISH

If the PTO clutch lever is shifted to "ON" (Engaged)
position under the following condition, the engine
stops automatically after standing up.
(1) The speed control pedal is not at "NEUTRAL"

position.

(2) The PTO select lever is not at "REAR PTO"

position.

(3) The parking brake is not applied.

PTO Drive Shaft

1. When using a PTO drive shaft, read the operator's

manual of the implement before operating the
implement.
PTO drive shafts are designed for specific machines
and power requirement.

2. To adjust the length of the PTO drive shaft, refer to the

following instructions.
(1) To adjust the length, hold the half shafts next to

each other in the shortest working position and
mark them.

(2) Shorten inner and outer guard tubes equally.
(3) Shorten inner and outer sliding profiles tube by

the same length as the guard tubes.

(4) Round off all sharp edges and remove burrs.

Grease sliding profiles.

3. Ensure that the PTO drive shaft is securely connected

at both ends before operating.

(1) Brake pedal
(2) Parking brake lock pedal
(3) PTO select lever
(4) PTO clutch lever
(5) Hand throttle lever
(6) Tachometer

"ON"

"INCREASE"

"OFF"

"DECREASE"

(1) Inner and outer sliding profile tubes
(2) Journal cross assy
(3) Fitting yoke
(4) Safety guard (In, Out)
(5) Chain

Содержание BX2350D







































































































Результаты поиска

Содержание BX2350D

Отзывы:

Бренды по названию

Популярные бренды

Kubota BX2350D, Руководство оператора

Результаты поиска

Содержание BX2350D

Отзывы:

Бренды по названию

Популярные бренды