KSB MK Скачать руководство пользователя страница 24

Страница: 24 / 64

5 Installation at Site

24 of 64

NOTE

Installing check and shut-off elements in the system is recommended, depending on
the type of plant and pump. However, such elements must not obstruct proper
drainage or hinder disassembly of the pump.

NOTE

If the pump is used for automatic drainage, fit a non-return or check valve.

The nominal diameters of the pipelines are equal to or greater than the nominal
diameters of the pump nozzles.

Adapters to larger nominal diameters are designed with a diffuser angle of
approx. 8° to avoid excessive pressure losses.

A flow velocity of 2-3 m/s is recommended.

The pipelines have been anchored in close proximity to the pump and connected
without transmitting any stresses or strains.

1. Thoroughly clean, flush and blow through all vessels, pipelines and connections

(especially of new installations).

2. Before installing the pump in the piping, remove the flange covers on the

suction and discharge nozzles of the pump.

CAUTION

Welding beads, scale and other impurities in the piping

Damage to the pump!

▷

Free the piping from any impurities.

3. If required, fit a suction strainer upstream of the pump nozzle.

4. Connect the discharge-side pump nozzle with the piping.

CAUTION

Aggressive flushing liquid and pickling agent

Damage to the pump!

▷

Match the cleaning operation mode and duration of flushing and pickling to
the casing materials and seal materials used.

5.6 Permissible forces and moments at the pump nozzles

No piping-induced forces and moments (from warped pipelines or thermal
expansion, for example) must act on the pump.

5.7 Electrical connection

DANGER

Incorrect electrical installation

Explosion hazard!

▷

For electrical installation, also observe the requirements of IEC 60079-14.

▷

Observe the manufacturer's product literature supplied with the motor.

▷

Observe the manufacturer's product literature supplied with the float switch if
float switch control is used.

Содержание MK

































































Результаты поиска

Содержание MK

Отзывы:

Похожие инструкции для MK

Бренды по названию

Популярные бренды

KSB MK, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MK

Отзывы:

Похожие инструкции для MK

Бренды по названию

Популярные бренды