KSB MK Скачать руководство пользователя страница 28

Страница: 28 / 64

6 Commissioning/Start-up/Shutdown

28 of 64

CAUTION

Abnormal noises, vibrations, temperatures or leakage

Damage to the pump!

▷

Switch off the pump (set) immediately.

▷

Eliminate the causes before returning the pump set to service.

The system piping has been cleaned.

The pump and the inlet tank, if any, have been vented and primed with the fluid
to be handled.

The lines for priming and venting have been closed.

CAUTION

Start-up against open discharge line

Motor overload!

▷

Make sure the motor has sufficient power reserves.

▷

Use a soft starter.

▷

Use speed control.

1. Close or slightly open the shut-off element in the discharge line.

2. Start up the motor.

3. Immediately after the pump has reached full rotational speed, slowly open the

shut-off element in the discharge line and adjust it to comply with the duty
point.

6.1.4 Shutdown

1. Close the shut-off element in the discharge line.

2. Switch off the motor and make sure the pump set runs down smoothly to a

standstill.

NOTE

If the discharge line is equipped with a non-return or check valve, the shut-off
element may remain open provided that the system conditions and system
regulations are considered and observed.

NOTE

If shut-off is not possible, the pump will run in reverse direction.
The reverse runaway speed must be lower than the rated speed.

For prolonged shutdown periods:

1. Close the auxiliary connections.

CAUTION

Risk of freezing during prolonged pump shutdown periods

Damage to the pump!

▷

Drain the pump and the cooling/heating chambers (if any) or otherwise protect
them against freezing.

Содержание MK

































































Результаты поиска

Содержание MK

Отзывы:

Похожие инструкции для MK

Бренды по названию

Популярные бренды

KSB MK, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MK

Отзывы:

Похожие инструкции для MK

Бренды по названию

Популярные бренды