KSB MK Скачать руководство пользователя страница 43

Страница: 43 / 64

7 Servicing/Maintenance

43 of 64

19. Pull shaft 210 out of sleeve 520.

20. Press sleeve 520 out of radial ball bearing 321.

21. Remove radial ball bearing 321 from thrust and radial bearing 303.01.

22. Remove grease-packed ring 500.01.

7.5 Reassembling the pump set

7.5.1 General information/Safety regulations

WARNING

Improper lifting/moving of heavy assemblies or components

Personal injury and damage to property!

▷

Use suitable transport devices, lifting equipment and lifting tackle to move
heavy assemblies or components.

CAUTION

Improper reassembly

Damage to the pump!

▷

Reassemble the pump (set) in accordance with the general rules of sound
engineering practice.

▷

Use original spare parts only.

Sequence

Always reassemble the pump in accordance with the corresponding general assembly
drawing.

Sealing elements

▪

Gaskets

– Always use new gaskets, making sure that they have the same thickness as

the old ones.

– Always fit gaskets of asbestos-free materials or graphite without using

lubricants (e.g. copper grease, graphite paste).

▪

O-rings

– Never use O-rings that have been made by cutting an O-ring cord to size and

gluing the ends together.

▪

Packing rings

– Always use pre-compressed packing rings.

CAUTION

Contact of O-ring with graphite or similar material

Fluid could escape!

▷

Do not coat O-ring with graphite or similar material.

▷

Use animal fats or lubricants based on silicone or PTFE.

▪

Assembly adhesives

– For gaskets, avoid the use of assembly adhesives if possible.

– If assembly adhesives are required, use a commercially available contact

adhesive (e.g. "Pattex").

– Only apply adhesive at selected points and in thin layers.

– Never use quick-setting adhesives (cyanoacrylate adhesives).

– Coat the locating surfaces of the individual components and screwed

connections with graphite or similar before reassembly.

– Prior to reassembly, screw back any forcing screws and adjusting screws.

Содержание MK

































































Результаты поиска

Содержание MK

Отзывы:

Похожие инструкции для MK

Бренды по названию

Популярные бренды

KSB MK, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MK

Отзывы:

Похожие инструкции для MK

Бренды по названию

Популярные бренды