KSB Amaprop 1200 Скачать руководство пользователя страница 1

Страница: 1 / 40

Amaprop

1592.893/4-10

Operating instructions

Mounting/Fastening Instructions

Installation Parts/Accessories

50 Hz

Sizes

1200

1400

1600

1800/1801

2000

2200

2500

These operating instructions contain fundamental information and precautionary

notes. Please read the manual thoroughly before installing or operating the unit.

These operating instructions must always be used in conjunction with the operating

instructions of the mixer and any other supplementary operating instructions

(e.g. lifting gear) concerning the mixer itself or its components.

These operating instructions also contain fundamental information about the instal-

lation and operation of the mixer accessories.

The responsibility for ensuring compliance with all regulations in force at the place

of installation -- also in the case of any temporary personnel assisting with the instal-

lation work -- lies with the user. Accessories must only be used in accordance with

their designated purpose and only on the KSB mixer(s) for which they are intended.

Their use on any other type of mixer of KSB origin or otherwise is not permitted.

The authorised, qualified personnel in charge of mounting the installation parts and

the installation of the submersible mixer itself is responsible that this be done in a

workmanlike manner.

Ident No.:

01 080 945

Содержание Amaprop 1200









































Результаты поиска

Содержание Amaprop 1200

Отзывы:

Похожие инструкции для Amaprop 1200

Бренды по названию

Популярные бренды

KSB Amaprop 1200, Инструкция по монтажу и установке

Результаты поиска

Содержание Amaprop 1200

Отзывы:

Похожие инструкции для Amaprop 1200

Бренды по названию

Популярные бренды