Krone X-Disc 620 Скачать руководство пользователя страница 47

Страница: 47 / 86

Operation

Pos: 53.10 /Überschriften/Überschriften 2/A-E/Abbau der Maschine @ 3\mod_1204792387824_78.docx @ 73245 @ 2 @ 1

8.2

Detaching the machine

Pos: 53.11 /BA/Sicherheit/Vorsätze/Gefahr - Maschine abstellen X-Disc @ 12\mod_1224742950045_78.docx @ 153301 @ @ 1

DANGER! – Unexpected movements of the machine

Effect: Danger to life, serious injuries
•

No one is permitted inside the danger zone.

•

Place the machine on solid and level ground only and with the parking supports extended.

•

You should not unhitch the machine until the engine has been switched off and the ignition
key has been removed.

•

Secure the forage harvester to prevent it from rolling back.

•

Use extreme caution when attaching implements to or detaching them from the forage
harvester! The accident prevention regulations must be complied with absolutely.

•

When detaching the machine, do not walk between the forage harvester and the machine!

Pos: 53.12 /BA/Bedienung /Vorsätze/Maisgebiss/Abbau/Schneidwerk ausheben @ 68\mod_1304420964999_78.docx @ 627351 @ @ 1

•

Lifting cutting system

Pos: 53.13 /BA/Bedienung /Hinweis Maschine stillsetzen @ 26\mod_1244443159144_78.docx @ 257575 @ @ 1

Note

Stop the machine.

Pos: 53.14 /BA/Bedienung /Vorsätze/EASYFLOW/Abbau T1 Bild X-Disc 620 @ 337\mod_1430206458918_78.docx @ 2559428 @ @ 1

Fig. 21

Pos: 53.15 /BA/Bedienung /Vorsätze/EASYFLOW/Abbau T2 EasyFlow 300/BV014 @ 160\mod_1365580006314_78.docx @ 1413300 @ @ 1

•

Swivel socket pin (3) of the parking supports (4) by 180° upward on both sides and pull
them out.

•

Pull out the parking supports (4) and lock them with socket pins (3) in the fifth hole from
below by a rotation of 180°.

Pos: 53.16 /WHB/Allgemeines/EasyFlow 3001/3801/Pickup abstellen EasyFlow 300/BV014 Hinweis @ 163\mod_1366097942243_78.docx @ 1424949 @ @ 1

Note

Always mark out the parking support in the fifth hole from below.

Pos: 53.17 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Содержание X-Disc 620























































































Результаты поиска

Содержание X-Disc 620

Отзывы:

Krone X-Disc 620, Оригинальная инструкция по эксплуатации, Страница: 47 / 86

Результаты поиска

Содержание X-Disc 620

Отзывы: