manualshive.com logo in svg

Krone Swadro 810, Руководство по эксплуатации, Страница: 45 / 64

Поделиться
Скачать
Krone Swadro 810 Скачать руководство пользователя страница 45

VI - 3

Care and maintenance

In case of repair, the tine arms can be individually
replaced by demounting.

•

Unscrew the screws (1) of the tine arm.

•

Undo the screws (2) of the neighbouring tine
arms.

•

Pull out tine arm (3) and replace defective parts.

•

When removing the tine arm, make sure that the
control roller is inserted into the track of curved
path.

•

Tighten all screws with the
torque required (105 Nm).

6.4

Replacing the tine arms (in
case of repair)

SW700031

3

1

2

6.5

Replacing the hydraulic hose
lines

Hydraulic hose lines are subject to ageing:
The characteristics of the hoses change due to effects of pressure, thermal load and UV
radiation. The date of manufacture is printed on the hydraulic hoses. This allows for the age to
be determined without lengthy searching. It is required by law that hydraulic lines are replaced
after a service life of six years.

Only use original spare parts as replacement hose lines!

Содержание Swadro 810

































































Отзывы:

Нет отзывов