Krone Swadro 810 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 64

Krone Swadro 810 Скачать руководство пользователя страница 25

III - 5

Preparing for Operation

The control unit can be used to preselect or control
several functions of the swather. Please observe the
following basic rules:

Always activate one function only on
the control unit.
The switches of all other functionss
must be set to neutral.
The control unit should be switched off
after any use to prevent functions being
activated inadvertently.

The following table shows the function of the different
switches.

3.3.5 Function of the switches on the

control unit (optional)

Item

Designation

Function

1

Main

Switches the control unit

switch

on and off

2

Indicator light

Lights up when the control

(green)

unit is switched on

3

Rocker switch

Raises or lowers the left hand

(touch-sensitive) rotor (when seen in the

travail direction)

4

Rocker switch Raises or lowers the right
(touch-sensitive)

hand rotor (when seen in
the travail direction)

SW700022

4

3

2

1

«
...
23
24
25
26
27
...
»

Содержание Swadro 810

































































Отзывы:

Нет отзывов