manualshive.com logo in svg

Krone Comprima F 125, Оригинальное руководство по эксплуатации

Оригинальное руководство по эксплуатации для пресс-подборщика Krone Comprima F 125 теперь доступно для бесплатного скачивания на {вебсайт}. Это необходимое руководство поможет вам максимально эффективно использовать ваше оборудование. Получите его прямо сейчас и ознакомьтесь со всеми функциями и настройками вашего Krone Comprima F 125.

Поделиться
Скачать
background image

II - 3

Safety

2.2.5 Hitched Implements

1. Secure implements against rolling.

2. Observe the maximum supported load on the

trailer coupling, swing drawbar or hitch!

3. If a drawbar coupling is used, make certain that

there is enough play at the coupling point!

2.2.6 PTO Operation

1. Use only PTO shafts specified by the

manufacturer!

2. The guard tube and guard cone of the PTO and

the PTO guard must be attached and in good
working condition (on the implement side, too)!

3. Make sure that the required tube covers are in

place for PTO shafts in transport and working
position!

4. Before installing or detaching PTO shafts,

disengage the PTO, switch off the engine and
remove the ignition key!

5. When using PTO shafts with an overload safety

or free-running coupling which are not shielded
by the guard on the tractor, mount the overload
safety or free-running coupling on the implement
side!

6. Always make sure that the PTO shaft is properly

installed and secured!

7. Attach chains to prevent the PTO shaft guard

from rotating with the shaft!

8. Before engaging the PTO shaft, make sure that

the selected PTO shaft speed of the tractor
matches the permissible implement speed!

9. Before engaging the PTO shaft, make sure that

no one is in the hazard area around the
implement!

10. Never engage the PTO shaft if the engine is

switched off!

11. No one should be in the vicinity of the rotating

PTO shaft when it is in use.

12. Always switch off the PTO shaft when the angle

is too large or the PTO shaft is not required!

 13. Caution! The flywheel will continue to rotate for

some time even after the PTO shaft has been
disengaged! Keep clear of the implement during
this time. Do not do any work on the implement
until the machine has come to a complete stand-
still and the flywheel has been secured using the
parking brake.

14. Cleaning, lubricating or adjusting PTO driven

implements or the PTO shaft only with PTO
disengaged, engine turned off and ignition key
withdrawn! Secure the fly-wheel with the parking
brake.

15. Place the disconnected PTO shaft onto the

bracket provided!

16. After detaching the PTO shaft, attach the

protective cover to the PTO shaft end!

17. If damage occurs, correct this immediately

before using the implement!

2.2.7 Hydraulic System

1. The hydraulic system is pressurized!

 2. When connecting hydraulic cylinders and

engines, make sure that the hydraulic hoses are
connected correctly!

3. When connecting the hydraulic hoses to the

tractor hydraulics, make sure that the hydraulics
of both the tractor and the implement have been
depressurized!

4. In the case of hydraulic connections between

tractor and implement, the coupling sleeves and
plugs should be marked to ensure a proper
connection!  If the connections are reversed, the
function will be reversed (e.g. raise/lower) - risk
of accidents!

5. Check the hydraulic hose lines at regular

intervals and replace them if damaged or worn!
The new hoses must fulfill the technical
requirements set by the manufacturer of the
implement!

6. When searching for leaks, use suitable aids to

avoid the risk of injuries!

Содержание Comprima F 125











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Comprima F 125

Dairyland SSD Operation Manual preview
SSD
Бренд: Dairyland Страницы: 21
Fisher Scientific Isotemp User Manual preview
Isotemp
Бренд: Fisher Scientific Страницы: 42
CAE Healthcare Ares User Manual preview
Ares
Бренд: CAE Healthcare Страницы: 108
Cannon CT-1000 Manual preview
CT-1000
Бренд: Cannon Страницы: 36
natus ALGO 5 Installation And Assembly Instructions preview
ALGO 5
Бренд: natus Страницы: 20
natus Dantec Keypoint G4 Hardware Instructions For Use preview
Dantec Keypoint G4
Бренд: natus Страницы: 42
natus Madsen Zodiac Reference Manual preview
Madsen Zodiac
Бренд: natus Страницы: 149
YASKAWA SI-P3V Technical Manual preview
SI-P3V
Бренд: YASKAWA Страницы: 40
Yardfully RAISED GARDEN BED Assembly Manual preview
RAISED GARDEN BED
Бренд: Yardfully Страницы: 2
Garmin GPSMAP 9 3 Series Owner'S Manual preview
GPSMAP 9 3 Series
Бренд: Garmin Страницы: 222
Numark NDX500 Operation Manual preview
NDX500
Бренд: Numark Страницы: 11
Emos ZYP0201 Quick Start Manual preview
ZYP0201
Бренд: Emos Страницы: 8
Lightolier F7000-19 Specification Sheet preview
F7000-19
Бренд: Lightolier Страницы: 2
Metrohm OMNIS 2.1006.0010 Product Manual preview
OMNIS 2.1006.0010
Бренд: Metrohm Страницы: 34
V&P Scientific SpinVessel 650ml Operating Instructions Manual preview
SpinVessel 650ml
Бренд: V&P Scientific Страницы: 9
PR Lighting LED Studio 3300D Product Manual preview
LED Studio 3300D
Бренд: PR Lighting Страницы: 16
Old Town Canoe Co. E1569 Installation Instructions preview
E1569
Бренд: Old Town Canoe Co. Страницы: 1
ESD C.2033.02 Hardware Manual preview
C.2033.02
Бренд: ESD Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды