background image

Page 20

B

C

A

The pilot will generally light with two or three pushes on the igniter.  Hold the knob in for about one (1) minute after the pilot

is lit.   Release knob and it will pop back out.  Pilot should remain lit.  If it goes out, repeat steps 4 through 8.

*If knob does not pop out when released, stop and immediately call your service 

 technician or gas supplier.

*If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and 

 call your service technician or gas supplier.

9. Push the control knob on the gas valve in slightly and turn 

counterclockwise            to the "ON" position.

Figure N-1

10. The burner can now be turned ‘ON’ or lit by pressing the

the ON/OFF rocker switch (C) located beside the valve OR by setting 
the thermostat or remote control to the desired setting.

         

11. NOTE:  When this fireplace insert is initially lit, condensation will

appear on the glass, this is normal in all gas fireplaces, 

and will disappear in one to three minutes.

TO TURN THE BURNER OFF:

To turn the burner ‘OFF’, depress the ON/OFF rocker switch to ‘OFF’, flip ‘off’ the wall switch, or adjust the setting on the

thermostat or remote control.  NOTE: The pilot will stay lit.

TO TURN THE PILOT OFF:

To turn off the pilot, push in and turn the control knob to the "OFF" position.  DO NOT FORCE.

NOTE:  A PAINT SMELL WILL OCCUR DURING THE FIRST FEW HOURS OF BURNING.  IT IS RECOMMENDED TO LEAVE THE FAN

OFF DURING THIS PERIOD AS THIS WILL SPEED UP THE PAINT CURING PROCESS.

INITIAL BURN PERIOD

DUE TO THE MAKEUP OF THE FIBER LOGS & REFRACTORY, THE CURING PROCESS MAY TAKE UP TO 4 HOURS OF BURN TIME.

DURING THIS PERIOD, THE LOGS & REFRACTORY WILL DISCOLOR, BUT WILL RETURN TO THEIR TRUE COLOR  ONCE THE

CURING PROCESS IS COMPLETE.  DO NOT BURN THIS FIREPLACE WITHOUT THE GLASS PROPERLY IN PLACE.

**MAKE SURE THE HOMEOWNER IS AWARE OF THIS**

NOTE:  Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or

clothing ignition.  Young children should be carefully supervised when they are in the same room as the appliance.

Clothing or other flammable material should not be placed on or near the appliance.

NOTE: THIS FIREPLACE MAY PRODUCE NOISES OF VARYING DEGREE  AS IT HEATS AND COOLS DUE TO

METAL EXPANSION AND CONTRACTION.  THIS IS NORMAL AND DOES  NOT AFFECT THE

PERFORMANCE OR LONGEVITY OF THE FIREPLACE.

   

Содержание CSK-31



































Отзывы: