kozy heat CSK-31 Скачать руководство пользователя

Страница: 3 / 34

Page 1

14 1/2"

30 7/8"

14 1/2"

19 1/4"

9 1/4"

9 1/8"

4 7/8"

1 7/8"

5 1/2"

14 1/2"

MODEL: #CSK-31 / #CSK-31-RF CHASKA

DIRECT VENT GAS FIREPLACE INSERT

INSTALLATION & OPERATING INSTRUCTIONS

IMPORTANT:

READ THIS MANUAL BEFORE INSTALLING AND USING THIS FIREPLACE

This fireplace has been tested to and complies with ANSI Z21.88-2005



CSA 2.33-2005 “VENTED GAS FIREPLACE HEATERS” by

OMNI-Test Laboratories, Beaverton, Oregon for U.S. & Canadian Installations. Installation must conform with local building codes

or in the absence of local building codes, with the National Fuel Gas code, ANSI Z223.1 NFPA 54 - Current Edition or the Natural

or Propane Installation Code, CSA B149-1.

SPECIFICATIONS:

Height (top of firebox): 19 1/4"
Width: 30 7/8"

Back Width: 23 1/8 "

Depth: 14 1/2”

Do not use this fireplace if any part has been under water.

Immediately call a qualified service technician to inspect

this appliance and to replace any part of the control

system and any gas control which has been under water.

COMMONWEALTH OF MASSACHUSETTS INSTALLATIONS

WARNING: This Product Must Be Installed By A Licensed Plumber
Or Gas Fitter When Installed Within The Commonwealth of
Massachusetts.

IMPORTANT: Installation of a CO detector is required in the
fireplace room.

WARNING: DO NOT REPLACE THIS BURNER WITH ANY

OTHER SIZED BURNER. REPLACEMENT WITH AN

UNAUTHORIZED BURNER CAN RESULT IN TEMPERATURES

EXCEEDING THE LIMITS FOR THIS FIREPLACE AND VOID

YOUR WARRANTY.

DUE TO HIGH TEMPERATURES, THIS FIREPLACE SHOULD

BE LOCATED OUT OF TRAFFIC AND AWAY FROM

FURNITURE AND DRAPERIES.

Warning: This Product Must be Installed By A Licensed

Plumber or Gas Fitter When Installed Within the

Commonwealth of Massachusetts.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED

WHEN THEY ARE IN THE SAME ROOM AS THIS FIREPLACE.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE

HAZARDS OF HIGH SURFACE TEMPERATURES AND

SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING

IGNITION.
CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD
NOT BE PLACED ON OR NEAR THE APPLIANCE

19 1/4"

Содержание CSK-31



































Результаты поиска

Содержание CSK-31

Отзывы:

Похожие инструкции для CSK-31

Бренды по названию

Популярные бренды

kozy heat CSK-31, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CSK-31

Отзывы:

Похожие инструкции для CSK-31

Бренды по названию

Популярные бренды