background image

 

 

 

 
 

 

 

 

Do not store or use gasoline or other flammable 
vapors and liquids in the vicinity of this or any 
other appliance. 

 
WHAT TO DO IF YOU SMELL GAS: 

 

  

Do not try to light any appliance. 

 

Do not touch electrical switches; do not use the 
phone in your building. 

 

Immediately call your gas supplier from a 
neighbor’s phone. Follow your gas supplier’s 
instructions. 

 

If you cannot reach your gas supplier, call the fire 
department. 

 
Installation & service must be performed by a qualified 
installer, service agency, or the gas supplier. 

WARNING: If the information in these instructions 
is not followed exactly, a fire or explosion may 
result, causing property damage, personal injury 
or loss of life. 

Models    #CSK-335 

 #CSK-335-RF 

 

CHASKA - XL 

Direct Vent Gas Fireplace Insert 

 

INSTALLATION & OPERATING 

MANUAL

 

This appliance may be installed in an aftermarket 
permanently located, manufactured (mobile) home, 
where not prohibited by local codes.  This appliance is 
only for use with the type(s) of gas indicated on the 
rating plate. This appliance is not convertible for use 
with other gases, unless a certified kit is used.

 

IMPORTANT: 

 

READ INSTRUCTIONS CAREFULLY BEFORE INSTALLATION.  

FAILURE TO INSTALL THIS FIREPLACE CORRECTLY CAN CAUSE 

SERIOUS STRUCTURAL AND FIRE HAZARDS AND MAY VOID 

YOUR WARRANTY. 

We recommend that our gas 
hearth products be installed 
and serviced by profes-
sionals who are certified in 
the U.S. by the National 
Fireplace Institute

®

 (NFI) as 

NFI Gas Specialists. 

www.nficertified.org 

This fireplace may be covered under one or more of 

the following U.S. Patents: 

#5,931,154 , #6,004,493, #6,029,655

 

www.kozyheat.com 

Sept. 2008 

CSK-335-R05 

Содержание Chaska-XL




































Отзывы: