background image

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS                        

For all sidewall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,  
including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than (7) feet above finished grade in the  
area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:    

INSTALLATION OF CARBON MONOXIDE DETECTORS 

At  time  of  installation  of  side  wall  horizontally  vented  gas  fueled  equipment,  the  installing  plumber  or  gas-fitter  shall  observe  that  a  hard  wired  carbon  
monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed.  In addition, the installing 
plumber  or  gas-fitter  shall  observe  that  a  battery  operated  or  hard  wired  carbon  monoxide  detector  is  installed  on  each  additional  level  of  the  dwelling,  
building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services 
of qualified licensed professionals for the installation of hard wired carbon monoxide detectors. 

  

 
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or attic, the hard wired carbon monoxide detector with 
alarm and battery back-up may be installed on the next adjacent floor level. 

 

 
In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days 
to comply  with the above requirements; provided, however, that during said thirty (30) day period, a battery  operated carbon  monoxide detector with an 
alarm shall be installed.   

APPROVED CARBON MONOXIDE DETECTORS 

Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS 
certified. 

SIGNAGE 

A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum of eight (8) feet above grade directly in line 
with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print no less the one-half inch 
(1/2) in size, 

 “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

  

INSPECTION 

The  state  or  local  gas  inspector  of  the  side  wall  horizontally  vented  gas  fueled  equipment  shall  not  approve  the  installation  unless,  upon  inspection,  the  
inspector  observes  carbon  monoxide  detectors  and  signage  installed  in  accordance  with  the  provisions  of  248  CMR  5.08  (2)  (a)  1  through  4. 

EXEMPTIONS 

The following equipment is exempt from 248 CMR 5.08 (2) (a) 1 through 4:The equipment listed in Chapter 10 entitled “Equipmen

t Not Required To Be 

Vented” in the most current edition of NFPA 54 as adopted by the Board; and Product Approved side wall horizontally vented ga

s fueled equipment installed 

in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. 

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED 

When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components 
with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include: 
  
 

Detailed instructions for the installation of the venting system design or the venting system components; and 

 
 

A complete parts list for the venting system design or venting system. 

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM  NOT PROVIDED 

When the manufacturer of Product Approved side wall horizontally vented gas equipment does not provide the parts for venting the flue gases, but identifies 

“special venting systems”, the following requirements shall be satisfied by the manufacturer:

 

 
 

The referenced “special venting systems” instructions shall be included with the appliance or equipment installation instruct

ions and;   

 
 

The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a pa

rts list and detailed  

 

installation instructions. 

 
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for 
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. 
 

NOTE 

The following requirements reference various Massachusetts and national codes not contained in this manual. 

Содержание 56150









































Отзывы: