background image

VENTING

 

Refer to vent system manufacturer's installation manual for complete installation instructions.  
Installation must conform with venting requirements and restrictions as outlined in this manual. 

 
 

 

Simpson Dura-Vent DV-GS  4” x 6-5/8” direct vent system  (horizontal and vertical terminations). 

Selkirk Metalbestos Chimney System 4” x 6-5/8” (horizontal and vertical terminations). 

Security Chimney System  4” x 6-5/8” (horizontal and vertical terminations). 

ICC Chimney System: 4” x 6-5/8” (horizontal and vertical terminations). 

RLH Chimney System: 4” x 6-5/8” (horizontal and vertical terminations). 

Amerivent / American metal Chimney System: 4” x 6-5/8” (horizontal and vertical terminations). 

Metal Fab Chimney System: 4” x 6-5/8” (horizontal and vertical terminations). 

This fireplace is designed to be used with rigid pipe only.

 

APPROVED VENTING

 

HORIZONTAL TERMINATIONS  

MINIMUM:    
3ft. (914mm)  vertical  + 90-degree elbow + 6in. (152mm) hori termination cap.  

 

MAXIMUM:  
3ft.  (914mm)  vertical  +  90-degree  elbow  +  21ft.  (6.40m)  horizontal  +  termination  cap.  

VERTICAL TERMINATIONS  

MINIMUM:    3ft. (914mm) hori termination cap.  

 

MAXIMUM:  40ft. (12.19m) hori termination cap.   

Figure 9b 

NOTE 

Horizontal sections require 1/4” (6mm) rise for every 12” (305mm) of travel. 

CAUTION 

This gas appliance must not be connected to or joined with any other chimney flue serving another appliance. 

NOTE 

Page 10 has information on restrictor installation in conjunction with venting installation. Page 16 has information on restrictor 
recommendations depending on burner flame appearance and instructions on installation after venting is completed. 

IMPORTANT 

Consult local and national installation codes to assure adequate combustion and ventilation air is available. 

 

Flame height and appearance will vary depending upon venting configuration and type of fuel used. 

 

This fireplace is manufactured with appropriate adaptor for proper connection to chosen approved venting. 

VERTICAL VENT SYSTEM CLEARANCES 

 

ALL SIDES 

ALL APPROVED VERTICAL PIPE 

1 inch (25mm) 

HORIZONTAL VENT SYSTEM CLEARANCES 

 

ALL SIDES 

ALL APPROVED HORIZONTAL PIPE 

1 inch (25mm) 

MIN: 3ft. (914mm) 
MAX: 40ft. (12.19m) 

Termination cap 

MIN: 6in. (152mm) 
MAX: 21ft. (6.40m) 
   
90-degree elbow 

3ft. (914mm) 

Figure 9a 

Termination  

cap 

Содержание 56150









































Отзывы: