manualshive.com logo in svg

kozy heat 56150, Руководство по установке

Поделиться
Скачать
kozy heat 56150 Скачать руководство пользователя страница 26

4 

This

 

optional #LKF-028 fan kit includes:   - 

Right & left fan assemblies - mounted  

                  - Fan cover plate   

 

 

 

 

        - Temperature control switch with magnet attached 

    - (4) Flange nuts 

 

 

 

 

        - Speed Control Box with 8ft. cord  

 

                       - (4) Phillips head screws (black)

 

OPTIONAL FAN KIT  

INSTALLATION OF THIS FAN SHOULD BE DONE ONLY BY A QUALIFIED INSTALLER 

WARNING 

MAKE  SURE  HOUSEHOLD  BREAKER  IS  SHUT  OFF  PRIOR  TO  WORKING  ON  ANY  ELECTRICAL  LINES. 
 
This appliance is equipped with a three-prong (grounding) plug for protection against shock hazard and should be plugged into 
a properly grounded three-prong receptacle.  Do not cut or remove grounding prong from plug. 

NOTE 

This  appliance  must  be  electrically  grounded  and  connected  in  accordance  with    local codes,  or  in  the  absence  of  local codes,  with  the  National 
Electrical Code, ANSI/NFPA 70 Current Edition, or the Canadian electrical Code CSA C22.1. 
 
This fan will not operate unless speed control has been turned ON and sufficient  heat has been applied to temperature control switch.  The fan will 
turn ON and OFF automatically as fireplace heats and cools. Adjust fan to desired speed while it is running. 
 
We recommend that an electrical outlet be installed near fireplace. 

Ground 

Before  adjusting  temperature  control  switch,  unplug  3-prong  plug  on  fan  cord  from  receptacle.   
Adjust  position  of  temperature  control  switch  to  a  warmer  location  under  firebox  to  turn  fan  ON 
sooner or move it to a cooler location under firebox to turn fan ON later. The fan will turn on when 
sensor in temperature control switch reaches 110° F and will turn OFF when sensor reaches 90° F. 
After adjustment, plug 3-prong plug on fan cord into receptacle

. 

TEMPERATURE CONTROL SWITCH POSITION

 

Temperature Control Switch 

Figure 4b 

1.  Locate (4) mounting studs underneath rear of fireplace. 

 

 

2.  Slide fan underneath fireplace, lift up, aligning (4) mount holes / slots in fan bracket to 

mounting studs under firebox. Secure with (4) nuts (included).   

  

3.  Attach  fan  cover  to  back  of  fireplace  by  aligning  holes  in  cover  to  holes  at  back  of  

fireplace. Secure with remaining (2) screws.   

 

4.  Mount speed control box onto left side of gas valve bracket by aligning slots in box to 

holes in bracket. Secure with (2) black phillips head screws, included.     

 

5.  Place temperature control switch (magnet attached) onto bottom of firebox as close to 

center as possible.  

   

6.  Plug fan cord into receptacle on speed control box.    

 

7.  Plug speed control box cord into a properly grounded three-prong receptacle.   

 

8.  Turn  speed  control  counter-clockwise  until  it  clicks.  This  is  the  OFF  position. 

 

9.  Turn speed control ON by turning knob clockwise past click - this is the highest setting. 

Figure 4a 

Содержание 56150









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды