background image

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

1

STK-LIN60-B KIT

INSTALLATION INSTRUCTIONS FOR STK-LIN60-B KIT

[FOR USE IN ALLUMEDLX60TEN-B, ALLUME60TEN-B, DRL4060TEN-B, AND DRL6060TEN-B FIREPLACES]

HEARTH PRODUCTS 

KITS AND ACCESSORIES

P/N 901058-00  REV. NC  07/2020

 WARNING 

This kit must be installed by a qualified installer, 

service agency, or gas supplier at the time of the 

fireplace installation. These instructions must 

be used in conjunction with the installation and 

operation manual provided with the fireplace. 

IMPORTANT NOTICE 

STK-LIN60-B KIT IS REQUIRED FOR UPGRADING FIREPLACE 

TO A SEE-THRU APPLICATION.

IMPORTANT NOTICE 

BLOWER USE IS NOT COMPATIBLE WITH THE STK-LIN60-B 

KIT.

GENERAL INFORMATION

The 

STK-LIN60-B KIT

 is designed to upgrade the fireplace to a 

see-thru application.
When Installing this kit, reference the framing dimensions for the 

see-thru application and follow the framing instructions shown on 

the fireplace installation Instructions. Follow all other installation 

requirements for the fireplace as detailed in the installation manual.

IMPORTANT! CONVERT THE FIREPLACE TO A SEE-THRU 

APPLICATION BEFORE INSTALLING INTO THE FRAMING.

REFER TO INSTALLATION INSTRUCTIONS AND CARE AND OPERA-

TIONS MANUAL (IICO) FOR FRAMING DETAILS BEFORE INSTALLING 

THIS KIT.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND 

OPERATION MANUAL PROVIDED WITH THE FIREPLACE APPLY TO 

THESE INSTRUCTIONS.

Kit Components

2 ea. Nailing Flange side
2 ea. Tile Stop L/R
2 ea. Tile Stop Top/Bottom
2 ea. Sight Obstructor
1 ea. Standoff Heatshield
1 ea. Door Access Cover
1 ea. Fireboard Assembly
1 ea. Glass Door
1 ea. Rear Standoff Assembly
1 ea. Barrier
22 ea. #10 Hex Head Screw
15 ea. #8 Phillips Head Screw
36 ea. Bugle drywall Screws

TOOLS REQUIRED (not included)

Electric Drill/Driver Gun
Phillips Screwdriver Bits
5/16 Nut Driver
5/16” Wrench

INSTALLER:  Leave this manual with the appliance 

CONSUMER:  Retain this manual for future reference

Fireboard 

Assembly

Nailing 

Flange L/R

Tile Stops 

L/R

Tile Stops 

Top/Bottom

Door Access 

Cover

Glass 

Door

Barrier

STK-LIN60-B KIT

Cat. No.

Model Number

Description

F4410

STK-LIN60-B KIT

Kit, Linear 60 See-Thru

Table 1  

  

See 

Figure 1

Figure 1 - STK-LIN60-B KIT

Sight Obstructors

Standoff

Heatshield

Rear Standoff

Assembly

Summary of Contents for STK-LIN60-B KIT







Reviews: