COMMISSION
kortho
QiC i-series
H325 IAE
Rev.: 004
7-4
1.
Adjustment block
2.
Clamp
3.
Positioning screws (2x),
X-axis
4.
Mounting plate offset screws
(2x)
5.
Gap adjustment screws with
locknut (4x)
6.
Coding unit mounting screw
(1x)
7.
Spring function lock screw
(1x)
8.
Mounting screw for
continuous printer (remove
this screw)
9.
Mounting plate offset screw
(1x)
10.
Compression springs screw
(2x)
11.
Coding unit mounting plate
Fig. 7.4
Coding unit adjustment block.
1.
Switch on the printer by operating the main switch on the control unit.
2.
Set the system operating pressure at 0.4 MPa (0,5 MPa for QiC 107i) using the air regulator.
3.
Loosen the spring function lock screw (10).
4.
Check whether mounting plate (11) can move freely between the offset screws (4 + 9). If not loosen
the offset screw (9).
5.
Loosen the lock nuts of the adjustment screws (5).
6.
Place and lock the magazine.
7.
Load the ‘Grid’ test label. (refer to section 9.1.1).
8.
Set the print density at 10%.
9.
Make some prints (when the preheat reached its set temperature) by pressing the test button.
10.
When using QiC Draw, download some scope-traces from de printer (via LAN connection).
Examine the diagrams for the speed characteristics, the average speed should be around
250mm/sec. Re-adjust the print speed if required by turning the speed adjustment screw in the
endblock tension (engineers option).
11.
Level the platen out with the print head by turning the four socket-screws (5) until a uniform, good
quality print is obtained. The gap between the print head and the substrate should be about 3 mm.
If so, the four lock nuts (5) need to be tightened. After tightening the lock nuts, re-adjust by means
of either the socket screws or density adjustment if necessary.
12.
Examine the print result Fig. 7.5, Fig. 7.6 and Fig. 7.7. If the print is good proceed, otherwise
readjust the printer according to the steps above.
Note:
Printing the Grid test label with a low density setting (e.g. 10%) makes it easier to see if the
printhead is level with the platen.
i
Содержание qic i series
