Kontron cPCI-MXS64 Скачать руководство пользователя страница 71

Страница: 71 / 132

Installing the Board

3-29

5. To engage the board’s connectors into the backplane connector, press

simultaneously on the front plate.

6. Fasten the module using the fellow-plate fixing screw to secure the module to the

system chassis.

To remove the module from the chassis, proceed as follows

1. Remove the front plate fixing screws.

2. Press the handle to act as a lever to disengage the CompactPCI connector from the

backplane.

3. Pull on the handle and gently remove the board.

3.5. cPCI I/O SIGNALS

This section describes integrated feature signals available on rear panel cPCI I/O
connectors (J3, J4, and J5)

3.5.1 J3 Signal Specification

3.5.1.1. Ethernet

LEDs

Signal

Pin Assignation

Description

LAN0, 1: SPLED

A6, E6

Speed LED signal

LAN0, 1: LINKLED

B6, D6

Link integrity LED signal

LAN0, 1:ACTLED

C6, A7

Transmit / receive activity LED signal

3.5.1.2. Ethernet

Signal

Pin Assignation

Description

LAN1:ETX+

Ethernet High Transmit Data line

LAN1:ETX-

Ethernet Low Transmit Data line

LAN1:ERX+

Ethernet High Receive Data line

LAN1:ERX-

Ethernet Low Receive Data line

Содержание cPCI-MXS64





































































































































Результаты поиска

Содержание cPCI-MXS64

Отзывы:

Бренды по названию

Популярные бренды

Kontron cPCI-MXS64, Техническое справочное руководство

Результаты поиска

Содержание cPCI-MXS64

Отзывы:

Бренды по названию

Популярные бренды