Kontron cPCI-MXS64 Скачать руководство пользователя страница 43

Страница: 43 / 132

3-1

3.1. SETTING JUMPERS

3.1.1 Jumper Description for the

PCI-MXS64

Description

VT-100 Mode (1-2)

When enabled, allows VT100 or ANSI terminal

connection

Download Mode (3-4)

When enabled, allows data serial download from

remote

computer.

Board Configuration

Defines if used with Front Access or Rear

Access

CompactFlash Setting

Use this connector to setup the CompactFlash

device in Master or Slave configuration.

Onboard Battery

Connects or Disconnects the battery to/from the

board

circuitry.

Remote Reset

To select Serial Port 1 or Serial Port 2 as a

source for the remote hardware reset.

SCSI Termination

Use this jumper to disable SCSI termination or

select the termination control method from

Software Controlled and Hardware Controlled

options.

Onboard Video

Use this jumper to enable or disable the onboard

video

feature.

Serial Port 2 Termination

Use these jumpers to connect or disconnect the

termination resistors on/from Serial Port 3 when

set for RS-422/RS-485 operation mode 0.

W8, W9

Содержание cPCI-MXS64





































































































































Результаты поиска

Содержание cPCI-MXS64

Отзывы:

Бренды по названию

Популярные бренды

Kontron cPCI-MXS64, Техническое справочное руководство

Результаты поиска

Содержание cPCI-MXS64

Отзывы:

Бренды по названию

Популярные бренды