System Units
Note
The guidelines for installation presented here must be regarded
as a base for detailed vessel specific plans prepared by the
installation shipyard. These plans should include drawings,
instructions and procedures specific to the ship in which the
equipment is to be installed.
6.2.1 Location
The EM 710 Transceiver Unit is normally installed in the vessel’s
“sonar room” close to the transducer arrays. This room must
be dry and free from excessive dust and vibration. Maximum
humidity of 80% is recommended. Good ventilation for the
equipment cooling must be provided.
Kongsberg Maritime recommends that this room is chosen close
enough to the transducer arrays so that you do not need to extend
the transducer cables.
The cabinet must be mounted on a bulkhead or on mounting
brackets welded to the bulkhead. Ensure that sufficient space is
provided around the unit to allow the unit’s doors to open fully.
Where space is restricted, it is possible to install the two 7H
high sub-racks without using the supplied cabinet. However,
it is then the responsibility of the customer to ensure adequate
environmental protection (heat, humidity, vibration, EMC etc.)
of the sub-racks.
The Transceiver Unit cabinet is fitted with a hinged front door
and a rear protection cover. This gives you access to the circuit
boards from both sides.
The unit is mounted on a support frame at the factory. This
frame is mounted on the bulkhead with two shock absorbers; one
mounted on top of the frame and one at the bottom.
Note that the space requirements for the Transceiver Unit must
be adhered to.
6.2.2 General information
The Transceiver Unit cabinet is fitted with a hinged front door
and a rear protection cover. This gives you access to the circuit
boards from both sides.
The unit is mounted on a support frame at the factory. This
frame is mounted on the bulkhead with two shock absorbers; one
mounted on top of the frame and one at the bottom.
Note that the space requirements for the Transceiver Unit must
be adhered to.
Transceiver Unit Outline dimensions
on page 127
164851/C
49
Содержание EM 710
