Komatsu WA470-7, Инструкция по сборке

Страница: 10 / 43

Selection of options
6 ×
Assembly procedure
5 ×
NO.0030
* An option setting is enabled when the starting switch is turned ON after changing the
setting and the starting switch is turned OFF and each controller on the machine is turned
off perfectly (about 15 seconds later).
On the "Option Select" screen, select an item with the UP (
▲
) and DOWN (
▼
) switches
and determine it with the ENTER switch, and set each item in order.
1-1. Option selecting function
★
Optional components installation setting table
Item name Default Remarks
Work Equipment Control TYPE A See "1-2. Change or setting of "Work Equipment Control""
Perform following setting according to installation state of
option and destination
･
If option is installed and destination is inside Japan, set
"JAPAN SPEC"
･
If option is installed and destination is outside Japan, set
"OTHERS"
･
If option is not installed, set "NO ADD"
Semi-auto Digging ADD Set "ADD" and do not change
Load Meter NO ADD If option is installed, select "ADD" (only JPN specification)
Perform following setting according to boom specification
･
If STD boom is installed, select "Standard"
･
If high-lift boom (optional) is installed, select "High Lift"
Auto Grease NO ADD If option is installed, select "ADD" (only EU specification)
Battery Electrolyte Level
Sensor NO ADD Set "NO ADD" and do not change
If di l d t l d i t t dj t it ith thi
Multicoupler NO ADD
Boom specification Standard
Ti Si C ti 0%
Q'ty Name Q'ty
Others
Tools to be used
Name
Facilities to be used
4 ×
Precautions
3 ×
* An option setting is enabled when the starting switch is turned ON after changing the
setting and the starting switch is turned OFF and each controller on the machine is turned
off perfectly (about 15 seconds later).
On the "Option Select" screen, select an item with the UP (
▲
) and DOWN (
▼
) switches
and determine it with the ENTER switch, and set each item in order.
1-1. Option selecting function
★
Optional components installation setting table
Item name Default Remarks
Work Equipment Control TYPE A See "1-2. Change or setting of "Work Equipment Control""
Perform following setting according to installation state of
option and destination
･
If option is installed and destination is inside Japan, set
"JAPAN SPEC"
･
If option is installed and destination is outside Japan, set
"OTHERS"
･
If option is not installed, set "NO ADD"
Semi-auto Digging ADD Set "ADD" and do not change
Load Meter NO ADD If option is installed, select "ADD" (only JPN specification)
Perform following setting according to boom specification
･
If STD boom is installed, select "Standard"
･
If high-lift boom (optional) is installed, select "High Lift"
Auto Grease NO ADD If option is installed, select "ADD" (only EU specification)
Battery Electrolyte Level
Sensor NO ADD Set "NO ADD" and do not change
If displayed travel speed is not correct, adjust it with this
function
If setting is increased 1%, travel speed increases 1% from 0%.
When tire of type 26.5 is installed, select "B"
(Do not select A which is for setting of tire of type 23.5)
Emergency Steering ADD If option is not installed, select "NO ADD"
J/S or FNR SWITCH NON When MF lever or right FNR (forward-reverse) switch is
installed, select "OPT FNR".
Lift Up Mode ADD Set "ADD" and do not change
E.C.S.S. ADD Set "ADD" and do not change
Torque Converter Lockup NO ADD Set "ADD" and do not change
4th Gear Prohibition NO ADD Set "NO ADD" and do not change
Perform following setting according to installation state of
option and destination
･
If option is installed and destination is inside Japan, set
"HEATER"
･
If option is installed and destination is outside Japan, set
"KOHAG"
･
If option is not installed, set "NO ADD"
F1 PWR CUT ADD Set "ADD" and do not change
Komatsu SmartLoader
Logic ADD Set "ADD" and do not change
Multicoupler NO ADD
Boom specification Standard
Two Stage Low Idle NO ADD
Tire Size Compensation 0%
Tire Type A
Others
1 × 2 ×
* An option setting is enabled when the starting switch is turned ON after changing the
setting and the starting switch is turned OFF and each controller on the machine is turned
off perfectly (about 15 seconds later).
On the "Option Select" screen, select an item with the UP (
▲
) and DOWN (
▼
) switches
and determine it with the ENTER switch, and set each item in order.
1-1. Option selecting function
★
Optional components installation setting table
Item name Default Remarks
Work Equipment Control TYPE A See "1-2. Change or setting of "Work Equipment Control""
Perform following setting according to installation state of
option and destination
･
If option is installed and destination is inside Japan, set
"JAPAN SPEC"
･
If option is installed and destination is outside Japan, set
"OTHERS"
･
If option is not installed, set "NO ADD"
Semi-auto Digging ADD Set "ADD" and do not change
Load Meter NO ADD If option is installed, select "ADD" (only JPN specification)
Perform following setting according to boom specification
･
If STD boom is installed, select "Standard"
･
If high-lift boom (optional) is installed, select "High Lift"
Auto Grease NO ADD If option is installed, select "ADD" (only EU specification)
Battery Electrolyte Level
Sensor NO ADD Set "NO ADD" and do not change
If displayed travel speed is not correct, adjust it with this
function
If setting is increased 1%, travel speed increases 1% from 0%.
When tire of type 26.5 is installed, select "B"
(Do not select A which is for setting of tire of type 23.5)
Emergency Steering ADD If option is not installed, select "NO ADD"
J/S or FNR SWITCH NON When MF lever or right FNR (forward-reverse) switch is
installed, select "OPT FNR".
Lift Up Mode ADD Set "ADD" and do not change
E.C.S.S. ADD Set "ADD" and do not change
Torque Converter Lockup NO ADD Set "ADD" and do not change
4th Gear Prohibition NO ADD Set "NO ADD" and do not change
Perform following setting according to installation state of
option and destination
･
If option is installed and destination is inside Japan, set
"HEATER"
･
If option is installed and destination is outside Japan, set
"KOHAG"
･
If option is not installed, set "NO ADD"
F1 PWR CUT ADD Set "ADD" and do not change
Komatsu SmartLoader
Logic ADD Set "ADD" and do not change
Multicoupler NO ADD
Boom specification Standard
Two Stage Low Idle NO ADD
Tire Size Compensation 0%
Tire Type A
7