manualshive.com logo in svg

Komatsu 75001, Руководство по ремонту

Поделиться
Скачать
Komatsu 75001 Скачать руководство пользователя страница 919

SEN03848-00

40-400

  42

WA250, 250PZ-6

400 Troubleshooting of electrical system (E-mode)

E-9 Headlamp, clearance lamp and tail lamp do not light up or go off

Contents of 

trouble

(4) Headlamp (high beam) does not light up or go off.

Related 

information

• The switch, lamp, or wiring harness of the headlamp (high beam) is disconnected or shorted with the 

ground.

• Carry out the following troubleshooting when the low beam lights up (goes off) normally.
• The input state (ON/OFF) to the machine monitor from the lamp switch (head lamp) can be checked 

with the monitoring function (Code: MONITOR PANEL 40900, D-IN-0).

• The input state (ON/OFF) to the machine monitor from the dimmer switch (high beam) can be 

checked with the monitoring function (Code: MONITOR PANEL 40904, D-IN-34).

Possible 

causes and 

standard value 
in normal state

Causes

Standard value in normal state/Remarks on troubleshooting

1 Broken bulb

If a specific headlamp does not light up, its bulb may be broken or 
may have a defective contact. Check the bulb directly.

2

Defective dimmer switch
(Internal trouble)

a

Prepare with starting switch OFF, then carry out troubleshooting 
without turning starting switch ON.

L04 (male)

Dimmer switch

Resistance

Between (5) and (3)

Low

Min. 1 M

z

High

Max. 1 

z

Between (4) and (3)

Low

Max. 1 

z

High

Min. 1 M

z

3

Disconnection in wiring har-
ness
(Disconnection or defective 
contact in connector)

a

Prepare with starting switch OFF, then carry out troubleshooting 
without turning starting switch ON.

Wiring harness between FLH (female) (C) – 
L04 (female) (5)

Resis-

tance

Max. 1 

z

Reference: Connector "FLH" is installed to both right and left sides.

4

Ground fault in wiring harness
(Contact with ground circuit)

a

Prepare with starting switch OFF, then carry out troubleshooting 
without turning starting switch ON.

Wiring harness between FLH (female) (C) – 
L04 (female) (5), – circuit branch end and 
ground

Resis-

tance

Min. 1 M

z

Reference: Connector "FLH" is installed to both right and left sides.

Содержание 75001














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды