Komatsu 75001 Скачать руководство пользователя страница 767

Страница: 767 / 1293

SEN03844-00

40-340

WA250, 250PZ-6

340 Troubleshooting by failure code (Display of code), Part 4

Failure code [DAJRKR] HST controller CAN-NET signal: Disconnection

When HST controller power supply circuit is defective

Possible causes

and standard

value in normal

state

Causes

Standard value in normal state/Remarks on troubleshooting

Broken fuse box FS1 fuse
No. 3

If fuse is broken, circuit probably has ground fault etc. (See cause c.)

Disconnection in wiring har-
ness (Disconnection in wiring
or defective contact in con-
nector)

Prepare with starting switch OFF, then carry out troubleshooting
without turning starting switch ON.

Wiring harness between fuse box FS1 fuse
No. 3 – HST (female) (1) (11).

Resis-

tance

Max. 1

Ground fault in wiring har-
ness (Contact with GND cir-
cuit)

Prepare with starting switch OFF, then carry out troubleshooting
without turning starting switch ON.

Between wiring harness fuse box FS1 fuse
No. 3 – HST (female) (1) (11), branch end
and ground

Resis-

tance

Min. 1 M

Between wiring harness L102 (female) (3) –
branch end and ground

Resis-

tance

Min. 1 M

Between wiring harness L101 (female) (2) –
D07 (female) (1), T07 (3) and ground

Resis-

tance

Min. 1 M

Between wiring harness L103 (female) (5) –
D08 (female) (1), T07 (1) and ground

Resis-

tance

Min. 1 M

Between wiring harness L104 (female) (5) –
R59 (female) (1) and ground

Resis-

tance

Min. 1 M

Between wiring harness L63 (female) (5), (1)
– HST (female) (25) and ground

Resis-

tance

Min. 1 M

Between wiring harness L15 (female) (3),
D01 (female) (5) – HST (female) (5) and
ground

Resis-

tance

Min. 1 M

Between wiring harness L15 (female) (2) –
HST (female) (34) and ground

Resis-

tance

Min. 1 M

Between wiring harness L15 (female) (4) –
L126 (female) (1), HST (female) (15) and
ground

Resis-

tance

Min. 1 M

Defective directional pres-
sure selector relay (L101)
(Internal short circuit)

Prepare with starting switch OFF, then carry out troubleshooting
without turning starting switch ON.

L101 (male)

Resistance

Between (5) – (6)

200 – 400

Prepare with starting switch OFF.

Test relay unit.

Directional pressure

selector relay (L101)

(1) – (2)

Resistance

Between (3) – (5)

When 24 V is applied

(relay is "ON")

Max. 1

Other than above

(relay is "OFF")

Min. 1 M

Prepare with starting switch OFF, then turn starting switch to
START and carry out troubleshooting.

Replace directional pressure selector relay (L101) with another
relay. If condition becomes normal, directional pressure selector
relay is defective.

Содержание 75001






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 75001

Отзывы:

Бренды по названию

Популярные бренды

Komatsu 75001, Руководство по ремонту

Результаты поиска

Содержание 75001

Отзывы:

Бренды по названию

Популярные бренды