Komatsu 75001 Скачать руководство пользователя страница 553

Страница: 553 / 1293

SEN03840-01

40-200

WA250, 250PZ-6

200 General information on troubleshooting

Classification and procedures of troubleshooting

Phenomena looking like troubles and troubleshooting Nos.

No.

Phenomena looking like trouble

Troubleshooting

Code

display

E-mode

H-mode

S-mode

Phenomena related to action codes and failure codes

1 Action codes are displayed on machine monitor

Check failure code

2 If failure code display function is checked, failure codes are displayed

Phenomena related to engine

3 Engine does not start easily (Starting performance is poor)

S-1

Engine does not start

Engine does not turn

E-1

S-2 a)

Engine turns but no exhaust smoke comes out

S-2 b)

Exhaust smoke comes out but engine does not
start (Fuel is injected)

S-2 c)

7 Engine does not pick up smoothly

S-3

8 Engine stops during operation

H-4

S-4

9 Engine does not rotate smoothly

S-5

10 Engine lacks output (or lacks power)

S-6

11 Exhaust smoke is black (Incomplete combustion)

S-7

12 Oil consumption is excessive (or exhaust smoke is blue)

S-8

13 Oil becomes contaminated quickly

S-9

14 Fuel consumption is excessive

S-10

15 Oil is in coolant (or coolant spurts back or coolant level goes down)

S-11

16 Oil pressure drops

S-12

17 Oil level rises (Entry of coolant or fuel)

S-13

18 Coolant temperature becomes too high (overheating)

S-14

19 Abnormal noise is made

S-15

20 Vibration is excessive

S-16

21 Preheater does not operate normally

E-2

Phenomena related to power train

22 The machine does not start

H-1

23 The travel speed is slow

H-2

24 The traction force is weak

H-3

25 Engine stalls when traveling or engine speed drops excessively

H-4

26 The gear is not shifted

H-5

27 Travel direction selection system does not function

E-6

Phenomena related to steering

28 The steering wheel does not turn

H-6

29 The steering wheel is heavy

H-7

30 Steering wheel shakes or jerks

H-8

31 Machine deviates naturally to one side when traveling

H-9

Phenomena related to brake

32 The brake does not work or does not work well

H-10

33 The brake is not released or is dragged

H-11

Содержание 75001






































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 75001

Отзывы:

Бренды по названию

Популярные бренды

Komatsu 75001, Руководство по ремонту

Результаты поиска

Содержание 75001

Отзывы:

Бренды по названию

Популярные бренды