manualshive.com logo in svg

Komatsu 75001, Руководство по ремонту

Поделиться
Скачать
Komatsu 75001 Скачать руководство пользователя страница 1007

SEN03851-01

50-100

  2

WA250, 250PZ-6

100 General information on disassembly and assembly

How to read this manual

How to read this manual

1

1.

Removal and installation of assemblies

Special tools

q

Special tools which are deemed neces-
sary for removal or installation of parts are
described as A1,• • •

X1 etc. and their part

names, part numbers and quantities are
described in the special tool list.

q

Also the following information is described
in the special tool list.

1)

Necessity

t

: Special tools that cannot be substi-

tuted and should always be used
(installed).

q

: Special tools that will be useful if avail-

able and are substitutable with com-
mercially available tools.

2)

Distinction of new and existing special
tools

N :

Tools newly developed for this

model. They respectively have a
new part number.

R :

Tools with upgraded part numbers.

They are remodeled from already
available tools for other models.

Blank: Tools already available for other

models. They can be used without
any modification.

3)

Circle mark 

Q

 in sketch column:

q

The sketch of the special tool is pre-
sented in the section of "Sketches of
special tools".

q

This mark means part No. of special
tools starting with 79 T-

-

and that they can not be supplied
from Komatsu in Japan (i.e. locally
made parts).

Removal

q

The “Removal” section contains procedures
and precautions for implementing the work,
know how and the amount of oil or coolant to
be drained.

q

General tools that are necessary for removal
are described as [1], [2]• • • etc. and their part
names, part numbers and quantities are not
described.

q

Various symbols used in the “Removal” section
are explained and listed below.

k

: This mark indicates safety-related precau-

tions that must be followed when imple-
menting the work.

a

: Know-how or precautions for work

[*1]  : This mark shows that there are instructions or

precautions for installing parts.

6

: This mark shows the amount of oil or coolant

to be drained.

4

: Weight of part or component

Installation

q

Except where otherwise instructed, installation
o f   pa rts   i s   d o n e   i n   t h e   r e v e rs e   o rd e r   o f
removal.

q

Instructions and precautions for installing parts
are shown with [*1] mark in the Installation
Section, identifying which step the instructions
are intended for.

q

General tools that are necessary for installa-
tion are described as [1], [2]• • • etc. and their
part names, part numbers and quantities are
not described.

q

Marks shown in the “Installation” section stand
for the following.

k

: Precautions related to safety in execution

of work.

a

: This mark gives guidance or precautions

when doing the procedure.

2

: Type of coating material

3

: Tightening torque

5

: Quantity of oil or coolant to be added

Sketches of special tools

q

Various special tools are illustrated for the con-
venience of local manufacture.

* *** ****

Содержание 75001














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды