manualshive.com logo in svg

Komatsu 75001, Руководство по ремонту

Поделиться
Скачать
Komatsu 75001 Скачать руководство пользователя страница 717

SEN03843-00

40-330

  46

WA250, 250PZ-6

330 Troubleshooting by failure code (Display of code), Part 3

Failure code [CA2186] Throttle sensor power supply low error

Failure code [CA2186] Throttle sensor power supply low error

1

Action code

Failure code

Trouble

Throttle sensor power supply voltage low error
(Engine controller system)

E03

CA2186

Contents of 

trouble

• Low voltage occurred in throttle sensor power supply circuit.

Action of 

controller

• Runs the engine at position of throttle 0% when accelerator pedal is OFF and at 50% when it is ON.
• Turns the centralized warning lamp and alarm buzzer ON.

Problem that 

appears on 

machine

• The engine does not reach full throttle.

Related 

information

• Method of reproducing failure code: Turn the starting switch ON.

Possible causes 

and standard 

value in normal 

state

Causes

Standard value in normal state/Remarks on troubleshooting

1

Ground fault in wiring har-
ness
(Contact with ground circuit)

a

Prepare with starting switch OFF, then carry out troubleshooting 
without turning starting switch ON.

Wiring harness between EC2 (female) (22) – 
PD1 (female) (1) and ground

Resis-

tance

Min. 

100 k

z

2

Short circuit in wiring har-
ness
(with another wiring harness)

a

Prepare with starting switch OFF, then carry out troubleshooting 
without turning starting switch ON.

Wiring harness among all pins between EC2 
(female) (9) – EC2 (female) (PD1 and 2, too, 
is disconnected.)

Resis-

tance

Min. 

100 k

z

3

Defective wiring harness 
connector

Connecting parts among accelerator pedal, engine unit wiring har-
ness, and engine controller are suspected. Inspect them directly.
• Loose connector, broken lock, broken seal
• Corrosive, bent, broken, forced-in, or extended pin
• Humidity in connector, entry of dirt or dust, poor insulation

4

Defective engine controller

If causes 1 – 3 are not detected, engine controller may be defective. 
(Since trouble is in system, troubleshooting cannot be carried out.)

Содержание 75001














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды