background image

 

17 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 

 

LIMITED WARRANTY

 

The KAPower module itself is guaranteed against defects in 

material and workmanship for three (3) years from date of 

purchase. The KAPower is a sealed unit. If the KAPower does 

not operate properly, it must be returned to the factory, 

prepaid, for replacement. If factory inspection determines the 

product to be defective under the terms of this warranty, it will 

be replaced without charge.  All other KSM components are 

guaranteed against defects in material and workmanship for 

one (1) year from the date of purchase. 

 

Failure due to accident, abuse, neglect, use other than in the 

intended application specified in this manual, improper 

installation or maintenance, mishandling, and repairs or 

attempted repairs which have been made by others, are not 

covered under the terms of this warranty.

 

Kold-Ban International, Ltd. shall not be liable for loss of use of 

the KAPower KSM or other incidental or consequential costs, 

expenses or damages incurred by the purchaser or user.

 

This warranty does not include labor for repair or replacement.

 

Kold-Ban International, Ltd.

 

8390 Pingree Road

 

Lake In The Hills, IL 60156-9637

 

(847) 658-8561 (800) 527-8278

 

Содержание KSM PLC



















Отзывы: