Kohler Aegis ELH775 Скачать руководство пользователя страница 91

Страница: 91 / 104

Reassembly

66 690 14 Rev. A

KohlerEngines.com

Install Push Rods and Rocker Arms

NOTE: Push rods must always be installed in same

position as before disassembly.

1. Note mark or tag identifying push rod as either

intake or exhaust for cylinder 1. Lightly apply engine

oil or grease to ends of push rods and install. Make

sure that each push rod ball seats in its respective

hydraulic lifter socket.

2. Apply grease to contacting surfaces of rocker arms

and rocker arm pivots. Install rocker arms and rocker

arm pivots on cylinder head.

3. Install new rocker arm screws with Dri-Loc® thread

locking compound on threads. Torque screws to

11.3 N·m (100 in. lb.). When tightening, use a steady

motion, without interruption, until proper torque is

achieved. Frictional heat from engaging threads may

otherwise cause locking compound to set

prematurely. If new screws are not available, apply

Loctite

242

to bottom 4 or 5 threads. Then install

and torque screws to 11.3 N·m (100 in. lb.).

4. Use a spanner wrench or rocker arm lifting tool (see

Tools and Aids) to lift rocker arms and position push

rods underneath.

5. Rotate crankshaft so piston in cylinder 2 is at top

dead center on compression stroke, and repeat

steps for remaining cylinder. Do not interchange

parts from one cylinder head with parts from other

cylinder head.

6. Rotate crankshaft to check for free operation of

valve train. Check clearance between valve spring

coils at full lift. Minimum allowable clearance is 0.25

mm (0.010 in).

Install Valve Covers

1. Make sure sealing surfaces of cylinder heads and

valve covers are clean and free of all old gasket

material.

2. Install new valve cover gaskets onto valve covers.
3. Install valve covers with gaskets in their original

locations.

4. Install lower mounting screws in #2 cover, and

nger

tighten only. Upper screws will be installed with air

cleaner bracket.

Install Hydraulic Lifters

NOTE: Hydraulic lifters should always be installed in

same position as before disassembly.

1. Refer to Disassembly/Inspection and Service for

lifter preparation (bleed down) procedures.

2. Apply camshaft lubricant (see Tools and Aids) to

bottom surface of each lifter. Lubricate hydraulic

lifters and lifter bores in crankcase with engine oil.

3. Install lifters into their respective lifter bores

according to location and cylinder number marked

during disassembly. Do not use a magnet.

Valve Stem Seals

These engines use valve stem seals on intake and

exhaust valves. Always use new seals whenever valves

are removed from cylinder head. Seals should also be

replaced if worn or damaged. Never reuse an old seal.

Assemble Cylinder Heads

Prior to installation, lubricate all components with engine

oil, paying particular attention to lip of valve stem seal,

valve stems and valve guides. Install following items in

order listed below using a valve spring compressor.

●

Valve stem seals

●

Intake and exhaust valves

●

Valve spring caps

●

Valve springs

●

Valve spring retainers

●

Valve spring keepers

Install Cylinder Heads

Cylinder Head Torque Sequence

Cylinder Head 1

Cylinder Head 2

NOTE: Match numbers embossed on cylinder heads

and crankcase.

1. Check to make sure there are no nicks or burrs on

sealing surfaces of cylinder head or crankcase.

2. Rotate crankshaft to position piston in cylinder 1 to

top dead center (TDC) on compression stroke.

3. Install a new cylinder head gasket.
4. Install cylinder 1 head onto number 1 side mounting

studs.

5. Install a plain washer onto each stud and secure

with a nut.

6. Torque nuts in two steps,

rst to 16.9 N·m

(150 in. lb.) and then to 33.9 N·m (300 in. lb.), using

torque sequence shown.

7. Repeat installation procedure for cylinder 2 side

head.

Содержание Aegis ELH775








































































































Результаты поиска

Содержание Aegis ELH775

Отзывы:

Похожие инструкции для Aegis ELH775

Бренды по названию

Популярные бренды

Kohler Aegis ELH775, Руководство по обслуживанию

Результаты поиска

Содержание Aegis ELH775

Отзывы:

Похожие инструкции для Aegis ELH775

Бренды по названию

Популярные бренды