Kohler Aegis ELH775 Скачать руководство пользователя страница 64

Страница: 64 / 104

Cooling System

66 690 14 Rev. A

KohlerEngines.com

Add coolant to over

ow reservoir as required, which

is a 50/50 mixture of ethylene glycol and water

(distilled or deionized water is recommended).

Drain Cooling System

Radiator Drain Plug Details

Radiator Drain Plug

1. Ensure engine is cool. When radiator is cool to

touch, slowly loosen radiator cap to

rst stop and

allow any pressure to bleed o

ﬀ

. Then loosen it fully

and remove it.

Loosen/remove radiator drain plug and allow coolant

to drain.

2. Remove

over

ow hose from reservoir. Unhook

inboard retainer and slide reservoir out of supports.

Pour out contents and wash or clean as required.

Dispose of all old coolant in accordance with local

ordinances.

3. Reinstall reservoir cap. Do not kink/pinch hose.
4. Flush cooling system.

Flushing Cooling System

NOTE: To prevent engine damage, do not pour water

into a hot engine. Do not operate engine without

coolant.

With system properly drained:
1. Fill cooling system with clean water and a cooling

system cleaner recommended for aluminum

engines. Follow directions on container.

2. Reinstall and tighten radiator cap.
3. Start and run engine for

ve minutes, or until it

reaches operating temperature. Stop engine and

allow it to cool.

4. Drain cooling system.
5. Fill cooling system.

Filling Cooling System

NOTE: To prevent engine damage, do not use

antifreeze mixture greater than 70% ethylene

glycol in cooling system. Do not use antifreeze

with stop-leak additive(s) or mix/add other

additives to cooling system. Use only ethylene

glycol antifreeze.

Cooling system capacity is approximately 2 liters

(2.18 qt.).
1. Check condition of cooling system hoses, clamps,

and associated components. Replace as required.

2. Fill with 2.0 L (2.1 U.S. qt.) equal parts of ethylene

glycol (anti-freeze) and water only. Distilled or

deionized water is recommended, especially in

areas where water contains a high mineral content.

Propylene glycol based anti-freeze is not

recommended.

3. Fill radiator with coolant mixture. Allow coolant to

drain into lower areas. Fill over

ow reservoir to a

level between FULL and ADD marks. Reinstall

radiator and reservoir caps.

4. Start and run engine for

ve minutes. Stop engine

and allow to cool.

5. Recheck coolant level in reservoir. Coolant level

should be between FULL and ADD marks. Add

coolant to reservoir if required.

Inspection

Cooling Fan Assembly, Belt, and Drive Pulleys
Cooling fan assembly, used to draw air through radiator,

is attached to a hub and pulley assembly with sealed

ball bearings. This assembly is belt driven o

ﬀ

ywheel,

via a lower split pulley, and requires very little service or

maintenance. DO NOT operate engine without fan and

properly functioning cooling system or engine damage

will occur.
1. Inspect fan for any cracks, damaged/missing fan

blades, and secure mounting.

2. Bearings in hub of pulley should rotate smoothly,

without roughness, binding, or play/wobble.

3. V-groove of each pulley (upper and lower) should

not be bent, nicked, or damaged. Pulley mounting

areas and lower pulley shims should be free of any

cracks or elongation.

4. Drive belt is designed and constructed for this

system. Do not use a substitute belt. Check overall

condition and replace belt if cracked, damaged, or

proper tension cannot be established by

repositioning of lower pulley shims. Use only Kohler

Part No. 66 203 02-S belt if replacement is

necessary.

See a Kohler authorized dealer for any necessary

service.

Содержание Aegis ELH775








































































































Результаты поиска

Содержание Aegis ELH775

Отзывы:

Похожие инструкции для Aegis ELH775

Бренды по названию

Популярные бренды

Kohler Aegis ELH775, Руководство по обслуживанию

Результаты поиска

Содержание Aegis ELH775

Отзывы:

Похожие инструкции для Aegis ELH775

Бренды по названию

Популярные бренды