Koganei FA Series Скачать руководство пользователя

Страница: 12 / 24

- 11 -

Operation depends on the setting of function selection

(1) When function selection

is set to

(instantaneous flow rate upper

limit switch)

After exceeding the instantaneous flow rate upper limit value and the switch turning

on, the settings for conditions to turn the switch off are set to hysteresis.

[Switch OFF Conditions] = [Instantaneous Flow Rate Upper Limit Value] – [Hysteresis]

Hysteresis is specified as a percentage (%) of the FS flow rate.

Setting value

Flow rate low

Flow rate high

Hysteresis

ON (OFF)

OFF (ON)

( ) indicate inverted output

Note: If the hysteresis threshold value is set below 0, the threshold

value becomes 0 and if the flow rate is minus, it turns off.

(2) When function selection

is set to

(instantaneous flow rate

lower limit switch)

After falling below the instantaneous flow rate lower limit value and the switch turns

on, the settings for conditions to turn the switch off are set to hysteresis.

[Switch OFF Conditions] = [Instantaneous Flow Rate Lower Limit Value] + [Hysteresis]

Hysteresis is specified as a percentage (%) of the FS flow rate.

( ) indicate inverted output

Setting value

Hysteresis

Flow rate low

Flow rate high

ON (OFF)

OFF (ON)

(3) When function selection

or (instantaneous flow rate range switch)

When

＞

, the

setting value is the upper limit and the

setting value is the lower limit.

When

＜

, the

setting value is the lower limit and the

setting value is the upper limit.

Operation does not work when

Hysteresis operation can be taken outside of the lower and upper limit setting

values as shown below.

Hysteresis is specified as a percentage (%) of the FS flow rate. Different settings can

be specified for the upper limit value and lower limit value.

ON (OFF)

OFF (ON)

( ) indicate inverted output

Setting value

Hysteresis

Flow rate low

Flow rate high

Hysteresis

Setting value

・

When

setting value

＜

setting value

ON (OFF)

OFF (ON)

( ) indicate inverted output

Setting value

Hysteresis

Flow rate low

Flow rate high

Hysteresis

Setting value

Note: If the hysteresis threshold value is set below 0, the threshold value becomes 0 and if the flow rate is minus, it turns off.

・

When

setting value

＞

setting value

Parameter setting list

Display item Item content Setting range

Default

Remarks

Analog output

20 mA flow rate

specification

Note 1

Flow rate value

equivalent to 0

to 400% FS can

be set.

Note 5

Depends

on model

number.

・

Initial default depends on model.

FAS-002

→

200

FAS-005

→

500

FAS-030

→

3000

FAS-060

→

6000

FAS-120

→

12000

・

Setting ranges are values with decimal

points removed. Decimal points will be

added with model settings.

・

Expected output cannot be obtained

when the setting values is less than 10%

of FS. Setting zero outputs fixed output

during an alarm.

・

Reconfigure this setting after changing

the display unit setting with function

selection

Analog output

4mA flow rate

specification

Note 1

Flow rate value

equivalent to 0 to 400%

FS can be set.

Note 5

・

Settings are values with decimal

points removed. Decimal points will

be added with model settings.

Instantaneous

flow rate switch

Output 1

Note 2

Flow rate value

equivalent to 0 to 400%

FS can be set.

Note 5

・

This setting can be configured

when function selection

set to

through

・

Settings are values with decimal

points removed. Decimal points will

be added with model settings.

・

Reconfigure this setting after

changing the display unit setting

with function selection

Switch output

hysteresis 1

Note 2

0 to 10% FS

flow rate

Switch output

on delay 1

Note 3

0 to 60 s

Instantaneous

flow rate switch

output 2

Note 2

Flow rate value

equivalent to 0 to 400%

FS can be set.

Note 5

・

This setting can be configured

when function selection

set to

・

Settings are values with decimal

points removed. Decimal points will

be added with model settings.

・

Reconfigure this setting after

changing the display unit setting

with function selection

Switch output

hysteresis 2

Note 2

0 to 10% FS flow

rate

Switch output on

delay 2

Note 3

0 to 60 s

Output

compensation factor

0.100

〜

2.000

1.000

Can be set in 0. 001 steps. Display value

is reflected in output. Changing setting

resets peak value and lower value.

Low flow cut 1

〜

％

Applied to both normal and back flow.

Maximum display

value

100

〜

200

％

200

Changes display range maximum value

from standard 200% of FS. When flow

rate exceeds setting value, set maximum

display value alternates with error display

(flow rate over).

Integration switch

setting value

lowest digits

00000

〜

99990

Can be configured when function

selection

is set to

through .

Integration

switch setting

value highest

digits

0000

〜

9999

Cost rate

Note 4

1.0

〜

100.0 100.0 Specifies the cost rate when cost is

displayed on information display.

Note 2: Instantaneous flow rate switch operation

Setup Guidelines

Note 1: Analog output scaling

Output for an instantaneous flow rate value is calculated using the formula

below.

([Indicated Flow Rate]−[4 mA Setting Value]) ×16

＋

4 [mA]

([20 mA Setting Value]−[4 mA Setting Value])

ｍ

A setting value : Instantaneous flow rate when 4 mA is output

ｍ

A setting value : Instantaneous flow rate when 20 mA is output

・

Minus flow output limit is 3. 2 mA, plus side output upper limit is 20. 8

mA.

・

When [4 mA Setting Value

]

≧

[20 mA Setting Value

], a

fixed output value will be output during an alarm.

・

When [20 mA Setting Value]−[4 mA Setting Value]

＜

10% of FS flow rate,

resolution is insufficient so desired output may not be possible.

Содержание FA Series

























Результаты поиска

Содержание FA Series

Отзывы:

Похожие инструкции для FA Series

Бренды по названию

Популярные бренды

Koganei FA Series, Инструкция по эксплуатации

Результаты поиска

Содержание FA Series

Отзывы:

Похожие инструкции для FA Series

Бренды по названию

Популярные бренды