y
HANDLING PROCEDURES AND PRECAUTIONS
●
Always observe the following items.
1. When using this product in pneumatic systems, always use
genuine KOGANEI parts or compatible parts (recommended parts).
When conducting maintenance and repairs, always use genuine
KOGANEI parts or compatible parts (recommended parts). Always
observe the required procedures.
2. Do not attempt inappropriate disassembly or assembly of the
product relating to basic configurations, or its performance or
functions.
KOGANEI cannot be responsible if these items are not properly
observed.
OTHER
Installation
Precautions on Use
1. Before inspections, cleaning, or maintenance, be sure to switch off
power supply.
2. If the supply air to the Blow Type unit is suspended for some time, a
red indicator could turn on.
3. If the tube metal section of the Blow Type unit is connected to a
ground, the unit will automatically be powered down.
4. In case the unit turns faulty, it will have to be adjusted and repaired by
specialized personnel. Contact Koganei for such a service.
5. To replace the discharging needle of the Blow Type unit, a dedicated tool
has to be used. The dedicated tool (
DTRY-ELB21
) is used in combination
with a torque-screwdriver that accepts the bit-socket illustrated below.
The dedicated tool is designed to prevent the discharging needle
and screws of the main unit from being broken under excessive
force. Try to limit the tightening torque to 19.6 N
・
cm {2 kgf
・
cm} or
less. If the discharging needle or the main unit is damaged because
the discharging needle was replaced without using the dedicated tool,
it will not be covered under our warranty.
6. The service life of the discharging needle varies depending on
the environmental conditions where it is used. A poor operating
environment (e.g., very humid conditions) or failure to clean the pin
will lead to degraded performance of the discharging needle. Hence,
periodic maintenance is required.
7. Take care to wire correctly. When the + side and the –side of the
power supply wiring are reverse-connected to the main unit of the
ionizer, a failure will occur.
8. When the power to the main unit of the ionizer is turned on immedi-
ately after being turned off, an abnormal output is produced. When
performing such an operation, be sure to allow at least 1 second or
longer after turning off.
ATTENTION
●
When considering the possibility of using this product in situations
or environments not specifically noted in the Catalog or Instruction
Manual, or in applications where safety is an important requirement,
such as in an airplane facility, combustion equipment, leisure
equipment, safety equipment and other places where human life or
assets may be greatly affected, take adequate safety precautions
such as applications with enough margins or fail-safe measures for
ratings and performance. Please consult KOGANEI with any
questions.
●
Always check the catalog and other reference materials for product
wiring and piping.
●
When handling the product, wear protective gloves, safety glasses,
safety boots, etc., to ensure safety.
●
When the product can no longer be used, or is no longer necessary,
dispose of it appropriately as industrial waste.
●
Do not use the Ionizer for any other purpose than the static
electricity removal.
1. For installation of the unit, pay attention to the contamination by oil or
water, high temperatures or high humidity. Especially, avoid a place
subject to dew condensation.
2. Install the ionizer in a place where ions can be sprayed on the charged
object, when the charged object is far from the other objects or is
suspended in the air.
Reason: Even if ions are sprayed on the charged object when it is near
other objects or in contact with them, no electrostatic removal can be
made.
3. If the ionizer is not grounded properly, static electricity removal level
will be reduced.
4. When mounting the fan, turbo-flow fan or wide-flow fan type ionizers,
do not thread mounting screws in 5mm or deeper; otherwise the
mounting screws may touch the inner circuit board.
5. When installing the fan, turbo-flow fan or wide-flow fan type ionizers,
ensure sufficient space so as not to block the suction opening, allow-
ing for the use of the airflow rate adjusting plate.
6.35
9
22
φ
4.5
※
Torque-screwdriver is sold separately.
Shape of the bit-socket
Содержание DTRY-ELB01
Страница 18: ... 7 memo memo ...
Страница 19: ...和文カタログ No C2152 w ...