manualshive.com logo in svg

Kodak Ektapro 4020, Руководство по обслуживанию

Kodak Ektapro 4020 - профессиональный проектор для слайдов, обеспечивающий высококачественное воспроизведение изображений. Для получения бесплатного сервисного руководства или инструкции по эксплуатации, загрузите его с manualshive.com. Наслаждайтесь качественным изображением с помощью Kodak Ektapro 4020.

Поделиться
Скачать
background image

MECHANISM FRAME and LENS MOUNT....................................................................................... 4-12

LENS MOUNT .................................................................................................................................. 4-13

Model 4020/7020 ...................................................................................................................... 4-15

RETAINER AF ASSEMBLY.............................................................................................................. 4-16

Model 5020/9020 and 9020/CINE ............................................................................................ 4-16

MECHANISM FRAME ...................................................................................................................... 4-18

AUTO FOCUS PCB and FOCUS MOTOR....................................................................................... 4-21

Master Board PCB ............................................................................................................................ 4-22

Master Board PCB Connectors ................................................................................................ 4-23

MICROCONTROLLER ............................................................................................................. 4-24

LOWER HOUSING ........................................................................................................................... 4-25

DUAL LAMP MODULE ..................................................................................................................... 4-26

DUAL LAMP MODULE............................................................................................................. 4-29

Lubrication ........................................................................................................................................ 4-30

5. DIAGNOSTICS ................................................................................................................................. 5-1

Diagnostic Overview EKTAPRO 4020/5020/7020/9020 and 9020/CINE ........................................... 5-1

Preparation ......................................................................................................................................... 5-3

Conditions:.................................................................................................................................. 5-3

No Function......................................................................................................................................... 5-4

Switch on Procedure Problems...................................................................................................... ..... 5-9

Lamp Problems EP 4020/5020/7020/9020 and 9020/CINE ............................................................. 5-12

Mirror Position................................................................................................................................... 5-17

Brightness Test......................................................................................................................... 5-17

Switch On Procedure ........................................................................................................................ 5-18

Switch On Procedure complete - No Keyboard Function ................................................................. 5-19

No function with REMOTE CONTROL ............................................................................................. 5-20

IR Remote Control .................................................................................................................... 5-20

Cable Remote ................................................................................................................................... 5-23

Service Manual

SM 2547-1

03/98

VI

Kodak AG, Stuttgart

Содержание Ektapro 4020









































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ektapro 4020

Yamaha YSP 1000 - Digital Sound Projector Five CH... Service Manual preview
YSP 1000 - Digital Sound Projector Five CH...
Бренд: Yamaha Страницы: 92
Euroscreen Connect Electric Manual preview
Connect Electric
Бренд: Euroscreen Страницы: 8
Energenie SIS-PWM Silver Shield User Manual preview
SIS-PWM Silver Shield
Бренд: Energenie Страницы: 20
Powerware TVSS ZoneMaster PLUS Installation Instructions & User Manual preview
TVSS ZoneMaster PLUS
Бренд: Powerware Страницы: 8
Barco WGA-510P User Manual preview
WGA-510P
Бренд: Barco Страницы: 11
CyberPower SB0502BA-DE User Manual preview
SB0502BA-DE
Бренд: CyberPower Страницы: 2
Chauvet Maverick Force 1 Spot Quick Reference Manual preview
Maverick Force 1 Spot
Бренд: Chauvet Страницы: 68
Claypaky RAIN SPOT 575 Instruction Manual preview
RAIN SPOT 575
Бренд: Claypaky Страницы: 24
ION Projector Plus Quick Start Manual preview
Projector Plus
Бренд: ION Страницы: 30
Mitsubishi Electric ProjectorView Global+ User Manual preview
ProjectorView Global+
Бренд: Mitsubishi Electric Страницы: 30
Avers Screens Contour User Manual preview
Contour
Бренд: Avers Screens Страницы: 9
Avers Screens Cumulus X Tension User Manual preview
Cumulus X Tension
Бренд: Avers Screens Страницы: 12
Avers Screens Stella Series User Manual preview
Stella Series
Бренд: Avers Screens Страницы: 2
Rompa 23008 Manual preview
23008
Бренд: Rompa Страницы: 9
Toshiba TheaterWide 62HM95 Specification preview
TheaterWide 62HM95
Бренд: Toshiba Страницы: 2
Toshiba TheaterWide 62HM94 Specification preview
TheaterWide 62HM94
Бренд: Toshiba Страницы: 2
Toshiba TheaterWide 62HM84 Specification preview
TheaterWide 62HM84
Бренд: Toshiba Страницы: 2
Toshiba TheaterWide 62HM15 Specifications preview
TheaterWide 62HM15
Бренд: Toshiba Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды