Kodak Ektapro 4020 Скачать руководство пользователя страница 43

Страница: 43 / 136

Slide Change Sequence

Projector Status:

SLIDE LIFTER down

SHUTTER is open

SLIDE is in GATE

LAMP is energized

Start:

“Forward”/"Reverse" BUTTON is pressed.

Signal from: P-Bus, Remote Control or Timer

The SHUTTER SOLENOID is deenergized.

The SLIDE LIFT MOTOR rotates clockwise to move the SLIDE LIFTER
up (max. 805 steps = one SLIDE LIFTER cycle).

The SLIDE LIFTER is in the up position when the CAM SENSOR
signal changes from not actuated to actuated.

If no:

the failure routine begins after 805 steps a without signal change.

If yes:

Starts the tray Motion. See page 3-10.

For details see page 3-10.

The SLIDE LIFT MOTOR moves clockwise to move SLIDE LIFTER
down. The MOTOR stops when signal changes from actuated to not
actuated.

When a TIMER is in use, a slide advance forward is done each time
after the selected interval is reached (Model´s 4020, 7020 external
timer, Model 5020, 9020 and 9020/CINE internal timer).

The slide is projected.

START

Close Shutter
Switch Autofocus Off

CAM
Sensor Signal
0 - 1
?

Yes

max. 805 Steps of
Slide Lift Motor

Start Tray Motion
Next slide position

Slide Lift Motor On

     Slide
in Gate Sensor
   actuated
         ?

Yes

Switch on Autofocus

Open Shutter

Timer
activated
?

Yes

End

Power LED blinking

Slide Lift Motor off

        CAM
Sensor Signal
   1 - 0
    ?

Yes

Slide Lift Motor off

Projector does not
operate

Write Failure into
Memory

figure 3-5

SM 2547-1

Service Manual

Kodak AG, Stuttgart

3-7

03/98

Содержание Ektapro 4020









































































































































Результаты поиска

Содержание Ektapro 4020

Отзывы:

Похожие инструкции для Ektapro 4020

Бренды по названию

Популярные бренды

Kodak Ektapro 4020, Руководство по обслуживанию

Результаты поиска

Содержание Ektapro 4020

Отзывы:

Похожие инструкции для Ektapro 4020

Бренды по названию

Популярные бренды