Kodak Ektapro 4020 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 136

background image

OEM ACCESSORIES

COPYRIGHT

The adapter of this English company is only designed to use traditional AV cassette recorders. Cue pulses
recorded on the tape trigger the interface unit to generate digital commands to advance the EKTAPRO Projector.
It is an interesting feature that the adapter works either by plugging directly into the remote socket or works
remotely by additional use of the EKTAPRO IR Receiver. In this case the system can simultaneously used with
both the EKTAPRO IR Transmitter and the adapter. The adapter is powered by a 9 volt A PP3 battery.

The illustration (figure 2-20) shows both possibilities to run the Projectors.

IR-USE.

The advantage is that the Adapter and Projector can be separated. In addition, the use of the
EKTAPRO Remote Transmitter is possible without disconnecting the Adapter.

CABLE USE

If no IR receiver is available the Adapter can be plugged with the fixed installed cable to the remote socket.

EKTAPRO IR Receiver

figure 2-20

Service Manual

SM 2547-1

03/98

2-16

Kodak AG, Stuttgart

«
...
28
29
30
31
32
...
»

Содержание Ektapro 4020









































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ektapro 4020

Бренд: NEC Страницы: 115

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 6

LT170 - XGA DLP Projector

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 2

LT75Z - MultiSync SVGA DLP Projector

Бренд: NEC Страницы: 49

MT1056 - MultiSync XGA LCD Projector

Бренд: NEC Страницы: 2

LT265 - INSTALLTION GUIDE

Бренд: NEC Страницы: 4

Бренд: Mitsubishi Страницы: 2

Бренд: THOMSON Страницы: 2

Бренд: B&B Electronics Страницы: 1

LightStyle LS-12d

Бренд: Runco Страницы: 152

Бренд: Kodak Страницы: 52

Бренд: Cineversum Страницы: 64

Бренд: Mitsubishi Страницы: 79

BEAMER 45BHM2550

Бренд: Salora Страницы: 14

Studio Experience Matinee 2HD

Бренд: BOXLIGHT Страницы: 56

Бренд: Hitachi Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды