Kodak Ektapro 4020 Скачать руководство пользователя страница 45

Страница: 45 / 136

Tray Motion Sequence:

a) Go To Zero Position

Projector Status:

- Energized

Signal from:

- P-Bus (Model´s 4020 and 5020 input only)
- Auto Zero (Model 9020 and 9020/CINE)

The MICROCONTROLLER selects shortest distance to the zero
position.

The TRAY MOTOR is energized.

The TRAY MOTION CONTROL delivers a step signal for each MOTOR
step.

The ZERO SENSOR delivers a signal if the position is reached

Failure:

A failure code is written into memory.
The power LED is blinking.

The position is reached. The TRAY POSITION in memory set to zero.

Close Shutter, Autofocus off, Move Slide

LIFTER in up position

Shortest

distance to Zero

Yes

Zero Sensor

actuated

Stop Tray Motor

Slide LIFTER Down

Set Tray Position

to Zero

END

Tray Motor ON

Reverse

Tray Motor On

Forward

More than

4 Step Signals

missed ?

Yes

Transport Failure

Write failure

into Memory

Projector does

not Operate

Zero Button

Power LED Blinking

figure 3-7

SM 2547-1

Service Manual

Kodak AG, Stuttgart

3-9

03/98

Содержание Ektapro 4020









































































































































Результаты поиска

Содержание Ektapro 4020

Отзывы:

Похожие инструкции для Ektapro 4020

Бренды по названию

Популярные бренды

Kodak Ektapro 4020, Руководство по обслуживанию

Результаты поиска

Содержание Ektapro 4020

Отзывы:

Похожие инструкции для Ektapro 4020

Бренды по названию

Популярные бренды