Kodak Ektapro 4020 Скачать руководство пользователя страница 42

Страница: 42 / 136

Switch On / Initialize Procedure

Projector Status:

Mechanic position is not known
Projector is energized

The MICROCONTROLLER starts the initialization routine:

- load the look-up tables
- look at the accessory slot and projector address
- sets the ECONOMY LAMP RELAY to 82V
- completes a Hardware reset

SLIDE LIFT MOTOR rotates clockwise (max. of 805 steps = one SLIDE
LIFTER cycle).

If SENSOR SIGNAL changes from not actuated to actuated, the SLIDE
LIFTER is in up position.
Yes = Start tray MOTION.
No = Begin a failure routine, after it has advanced 805 steps without
sensor signal change.

slide tray moves forward about 3,5 slides (with software version above
4.2).

Details about tray motion can be obtain from page 3-9.

If the ZERO SENSOR is not actuated, the tray reverses

If the ZERO SENSOR is not actuated, the slide tray continues to
advance.

The SLIDE LIFT MOTOR moves clockwise.

When the CAM SENSOR changes from actuated to not actuated, the
LIFTER is in the down position.

If the SLIDE IN GATE SENSOR is actuated, the SHUTTER opens.

Yes

START

Microcontroller
is active

Slide LIFT MOTOR On.Move
LIFTER to Up Positon

CAM Sensor
Signal
0 - 1

Move Slide Tray
about 3 Slides forward

Zero
Sensor actuated
?

Reverse Slide Tray

Zero
Sensor actuated
?

Stop Tray Motor

Slide LIFT MOTOR On
Slide LIFTER to Down Positon

    CAM Sensor
    Signal
           1 - 0

Slide in Gate
Sensor actuated
?

Open Shutter
Autofocus On

Projector Ready
for Operation

END

Stop LIFT MOTOR

Power LED Blinking

Write the Failure into
Memory

Projector does not
Operate

Stop LIFT MOTOR

Yes

Stop LIFT MOTOR

figure 3-4

Service Manual

SM 2547-1

03/98

3-6

Kodak AG, Stuttgart

Содержание Ektapro 4020









































































































































Результаты поиска

Содержание Ektapro 4020

Отзывы:

Похожие инструкции для Ektapro 4020

Бренды по названию

Популярные бренды

Kodak Ektapro 4020, Руководство по обслуживанию

Результаты поиска

Содержание Ektapro 4020

Отзывы:

Похожие инструкции для Ektapro 4020

Бренды по названию

Популярные бренды