Kodak Ektapro 4020 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 136

background image

EKTAPRO Model 4020

Adjustable Tray Motion

:

Tool PN 622 0454 has to used on Projectors from SN 85 xxx and
above

Manual elevator mechanism :

Two height adjustment feet are attached on the front side of the

Projector

Indicator LED on front

:

LED continuously on Projector O.K. If the LED is blinking fast a slide
jam occurs. In standby mode the LED is blinking short off and long on.
If the LED is blinking continuously (on/off) a checksum error occurs
(only during programming the processor)

Remote SOCKET

:

8 pin mini DIN

Slide change buttons

:

A single step will happen after pressing the “Forward" or the “Reverse”
button less than 0.9s. Multiple steps will be done by pressing the
“Forward” button more than 0.9s

A run into the “Zero” position will immediately be done after press and
hold the “Reverse” button until the Slide Tray is in “Zero” position

Last Lamp used

:

After switching on the Projector the last used lamp will be selected

(memory function). This memory function can be disabled by pressing
the STANDBY button during switching on the projector

Line up

:

Pressing both transport keys will enable the lamp to adjust the projector

(green LED on the Backpanel is blinking). The Standby key will disable
this function

NEW

In case of using a IR Remote Control single steps are possible independent how long the button is pressed.

By pressing the “Reverse button” on the IR Remote Control random access is possible.

To select the Slide Tray capacity (80 or 140 slides) a ball point pen or a small screwdriver has to be used.

The Lamp Module has no longer a Heat Absorbing Glass installed. Due to the new mirror the light output is

increased up to 30%.

NOTE

In case of changing the mirror take care of the type (see NEWSLETTER #4).

SM 2547-1

Service Manual

Kodak AG, Stuttgart

2-3

03/98

«
...
15
16
17
18
19
...
»

Содержание Ektapro 4020









































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ektapro 4020

DS1-MP10RX series

Бренд: NEC Страницы: 39

Бренд: Christie Страницы: 4

Бренд: M-system Страницы: 8

Бренд: Laserworld Страницы: 12

Бренд: ViewSonic Страницы: 2

Бренд: Grandview Страницы: 4

Бренд: Furman Страницы: 60

ActivExpression 2

Бренд: promethean Страницы: 26

Бренд: Mitsubishi Страницы: 71

Бренд: Kramer Страницы: 4

BEAMER 45BHM2550

Бренд: Salora Страницы: 14

Бренд: Epson Страницы: 8

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 12

Бренд: Epson Страницы: 131

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды