3
COMPOUND MITER SAW SAFETY
SPECIFIC SAFETY INSTRUCTIONS FOR THIS
COMPOUND MITER SAW
1. DO NOT USE THIN KERF BLADES they can deflect and
contact guard and can cause possible injury to the operator.
2. DO NOT operate the miter saw until it is completely
assembled and installed according to these instructions.
3. IF YOU ARE NOT thoroughly familiar with the operation
of miter saws, seek guidance from your supervisor,
instructor or other qualified person.
4. ALWAYS hold the work firmly against the fence and
table. DO NOT perform any operation free hand
(use clamp wherever possible).
5. KEEP HANDS out of the path of the saw blade. If the
workpiece you are cutting would cause your hands to be
within 6-3/4 in. of the saw blade, the workpiece should
be clamped in place before making the cut.
6. BE SURE the blade is sharp, runs freely and is free
of vibration.
7. ALLOW the motor to come up to full speed before
starting a cut.
8. KEEP THE MOTOR AIR SLOTS CLEAN and free
of chips or dust.
9. ALWAYS MAKE SURE all handles are tight before cutting,
even if the table is positioned in one of the positive stops.
10. BE SURE both the blade and the collar are clean and the
arbor bolt is tightened securely.
11. USE only blade collars specified for your saw.
12. NEVER use blades larger in diameter than 10 inches.
13. NEVER apply lubricants to the blade when it is running.
14. ALWAYS check the blade for cracks or damage before
operation. Replace a cracked or damaged blade
immediately.
15. NEVER use blades recommended for operation
at less than 4800 RPM.
16. ALWAYS keep the blade guards in place and
use at all times.
17. NEVER reach around the saw blade.
18. MAKE SURE the blade is not contacting the workpiece
before the switch is turned ON.
19. IMPORTANT: After completing the cut, release the
trigger and wait for the blade to stop before returning the
saw to the raised position.
20. MAKE SURE the blade has come to a complete stop
before removing or securing the workpiece, changing
the workpiece angle or changing the angle of the blade.
21. NEVER cut metals or masonry products with this tool.
This miter saw is designed for use on wood and
wood-like products.
22. NEVER cut small pieces. If the workpiece being cut may
lead your hand or fingers to be within 6-3/4 in. of the saw
blade, the workpiece is too small.
23. PROVIDE adequate support to the sides of the saw table
for long work pieces.
24. NEVER use the miter saw in an area with flammable
liquids or gases.
25. NEVER use solvents to clean plastic parts. Solvents could
possibly dissolve or otherwise damage the material.
26. SHUT OFF the power before servicing or adjusting
the tool.
27. DISCONNECT the saw from the power source and clean
the machine when finished using.
28. MAKE SURE the work area is clean before leaving
the machine.
29. SHOULD any part of your miter saw be missing,
damaged, or fail in any way, or any electrical component
fail to perform properly, lock the switch and remove the
plug from the power supply outlet. Replace missing,
damaged, or failed parts before resuming operation.
ELECTRICAL REQUIREMENTS AND SAFETY
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for electric
currents and reduces the risk of electric shock. This tool is
equipped with an electrical cord that has an equipmentground-
ing conductor and a grounding plug. The plug must be plugged
into a matching receptacle that is properly installed and
grounded in accordance with all local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED.
If it will not fit the receptacle, have the proper receptacle in-
stalled by a qualified electrician.
IMPROPER CONNECTION of the equipment grounding con-
ductor can result in risk of electric shock. The conductor with
the green insulation (with or without yellow stripes) is the
equipment grounding conductor. If repair or replacement of
the electrical cord or plug is necessary, do not connect the
equipment grounding conductor to a live terminal.
CHECK with a qualified electrician or service person if you do
not completely understand the grounding instructions, or if
you are not certain the tool is properly grounded.
USE only three-wire extension cords that have three-pronged
grounding plugs with three-pole receptacles that accept the
tool’s plug. Repair or replace damaged or worn cords imme-
diately.
GUIDELINES FOR EXTENSION CORDS
USE THE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. Use an extension cord
heavy enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting in
loss of power, overheating and burning out of the motor. The
table on the right shows the correct size to use depending
on cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge number, the
heavier the cord.
