GUIA PARA LA SOLUCION DE PROBLEMAS
MEDIDAS CORRECTIVAS SUGERIDAS
1. Inspeccione, limpie o reemplace las escobillas. Vea
la sección de MANTENIMIENTO.
2. Utilice una hoja recomendada. Deje que se
enfríe. Vea la sección EXTRACCION
O INSTALACION DE LA HOJA
3. Vuelva a ajustarlo. Vea la sección EXTRACCION
O INSTALACION DE LA HOJA.
4. Reemplace los cepillos.
5. Centro de servicio de Knova.
1. Revise y utilice un fusible de retardo de 15 A
o un interruptor de circuitos. Vea la sección de
Requisitos Electricos.
2. Reemplace las escobillas. Vea la sección de
MANTENIMIENTO.
3. Verifique si existen suministro electricidad en el
tomacorriente.
1. Esto es normal.Vea la sección de MANTENIMIENTO.
2. Centro de servicio de Knova.
PROBLEMA
El freno no
detiene la hoja
antes de que
transcurran 7
segundos.
EI motor no
arranca.
Se produjeron
chispas en las
escobillas cuando
liberó el interruptor.
CAUSA DEL PROBLEMA
1. Las escobillas del motor no están selladas o
están apenas adheridas.
2. El freno del motor se sobrecalienta debido a la
utilización de una hoja de tamaño inadecuado
o a un ciclo de ENCENDIDO y APAGADO rápido.
3. El perno del árbol está flojo.
4. Los cepillos están partidos, dañados etc.
5. Otra.
1. El interruptor límite falla.
2. Una de las escobillas está desgastada.
3. Hay un fusible quemado o el interruptor de
circuito está desconectado del tablero principal.
1. Una de las escobillas está desgastada.
2. Otra.
GUIA PARA LA SOLUCION DE PROBLEMAS - MOTOR
Para evitar lesiones por encendidos accidentales, APAGUE y desconecte siempre la herramienta
antes de moverla, reemplazar las hojas o hacer ajustes.
ADVERTENCIA
46
MEDIDAS CORRECTIVAS SUGERIDA
1. Vea la sección de AJUSTES- Sección del recorrido
del brazo del corte.
1. Vea la sección de FUNCIONAMIENTO Sección del
AJUSTE DEL ÁNGULO DE LOS INGLETES.
2. Aspire o sople el aserrín. UTILICE PROTECCION
PARA LOS OJOS.
1. Centro de servicio de Knova.
1. Afloje la tuerca para asegurar el perno de pivote.
2. Centro de servicio de Knova.
3. Limpie y lubrique las piezas móviles.
1. Vea la sección de UTILIZACION ELEMENTAL DE LA SIERRA.
2. Reemplace o afile la hoja.
3. Reemplácela por una hoja de 10” de diámetro.
4. Utilice la abrazadera de sujeción inferior para
asegurar la pieza de madera a la tabla.
1. Reemplace la hoja.
2. Apriete el perno del árbol.
PROBLEMA
La hoja golpea
contra la mesa.
El ángulo de corte
no es el correcto.
No puede ajustar
el inglete.
El brazo de corte
se tambalea.
El brazo de corte
no se levanta por
completo o el
protector de la
hoja no se cierra
por completo.
La hoja se
atasca,
queda
obstruida
o quema la
madera.
La sierra vibra
o se sacude.
CAUSA DEL PROBLEMA
1. Desalineación.
1. la mesa de ingletes no está trabada.
2. Hay aserrín debajo de la mesa.
1. Los pernos de pivote están flojos.
1. El perno de pivote está muy alto.
2. El resorte de pivote no ha sido reemplazado
debidamente luego del mantenimiento.
3. Se ha acumulado aserrín.
1. Funcionamiento inadecuado.
2. La hoja está desafilada o deformada.
3. El tamaño de la hoja es inapropiado.
4 La madera se mueve al cortarla.
1. La hoja de la sierra no redondea, está
dañada/ está floja.
2. El perno del árbol está flojo.
GUIA PARA LA SOLUCION DE PROBLEMAS - FUNCIONAMIENTO DE LA SIERRA
MEDIDAS CORRECTIVAS SUGERIDAS
1. Reemplace con baterías AAA nuevas.
2. Recargue las baterías y cerciórese de que tengan
buen contacto con el resorte para las baterías.
PROBLEMA
La guía láser
no se
enciende.
CAUSA DEL PROBLEMA
1. Las baterías están agotadas.
2. Los contactos de la batería necesitan
ajustarse.
GUIA PARA LA SOLUCION DE PROBLEMAS - GUIA LASER